Table of Content

Power and Signal Pin Assignment

How to Use This Guide

  • This guide is split into two tables:
    • Module Power Connection Table section shows the power source of the different FPGA banks and components of the different module boards as well as the power and group location on the B2B connectors of the module site.
    • Carrier Board Power Connection Table section shows the power source of the B2B connectors with pins, schematic names and available options of the different carrier boards as well as the power location on the B2B connectors of the carrier site.

  • The PCBs have fixed and variable user supplied I/O voltage pins. Variable power supply pins are colored in four groups (VCCIOA, VCCIOB, VCCIOC and VCCIOD).
  1. Find your module model on the Module Power Connection Table and check the power supply of the different FPGA banks.
  2. If the power supply is variable(colored), go to the Carrier Board Power Connection Table and see how it's connected on your carrier board. Often the power source can be selected by jumper, resistor or variable used from other connector pin of the carrier board. So use the schematic name or the component designator from the table to search for the available options in the PCB schematics or TRM.
  3. Additional Master Pinout Viewer/XDC-Generator  is available on Trenz Electronic Download - Pinout

Module Power Connection Table

Group123456789special
Module ModelBankIOsTypeVoltageBankIOsTypeVoltageBankIOsTypeVoltageBankIOsTypeVoltageBankIOsTypeVoltageBankIOsTypeVoltageBankIOsTypeVoltage


TE0710B1548HRVCCIOA--------B3450HRVCCIODB166HR3.3VB148HR3.3V2x 100Mbit ETH





TE0711B1548HRVCCIOAB3436HRVCCIOBB1418HR3.3VB3550HRVCCIODB166HR1.8VB148HR3.3VB348HRVCCIOBB34(4)USB
TE0712

B16

48HRVCCIOAB1320HRVCCIOBB1418HR3.3VB1550HRVCCIODB136HRVCCIOBB148HR3.3V

1x 100Mbit ETH / B13

4HRVCCIOB
B144x GTP on G2
TE0713





























4x GTP on G2

TE0715
with Z-7015
Z-7012S

B1348HRVCCIOAB3416HRVCCIOCB3418HRVCCIOCB3550HRVCCIODB5016MIO1.8VB5008MIO3.3V1x Gbit ETH


SGMIIUSB4x GTP on G2
TE0715
with Z-7030
B1348HRVCCIOAB3416HPVCCIOCB3418HPVCCIOCB3550HPVCCIODB5016MIO1.8VB5008MIO3.3V1x Gbit ETH


SGMIIUSB4x GTP on G2
TE0720B3548HRVCCIOAB3436HRVCCIOBB3318HRVCCIOCB1350HRVCCIODB5016MIO1.8VB5008MIO3.3V1x Gbit ETH


SGMIIUSB
TE0820*B6648HPVCCIOA B6516 HP VCCIOC B6518 HP VCCIOCB6450 HPVCCIODB5016MIO3.3V B5018MIO3.3V1x Gbit ETH


 SGMII USB4x GTR on G2
TE0821*B2648HDVCCIOA B6516 HP VCCIOC B6518 HP VCCIOCB2448HDVCCIODB5016MIO3.3V B5018MIO3.3V1x Gbit ETH


 SGMII USB4x GTR on G2
TE0823*B6648HPVCCIOA B6516 HP VCCIOC B6518 HP VCCIOCB6450 HPVCCIODB5016MIO3.3V B5018MIO3.3V1x Gbit ETH


 SGMII USB4x GTR on G2
TE0741B1348HRVCCIOAB1616HRVCCIOBB1518HRVCCIOCB1250HRVCCIOD1x GTX1 Lane

B148HR3.3V2x GTX2 Lanes

1x GTX
4x GTX on G2
TE0742*






























TE0841B6448HRVCCIOAB6616HPVCCIOBB6818HPVCCIOCB6750HPVCCIOD1x GTH1 Lane

B658HR3.3V2x GTH2 Lanes

1x GTH
4x GTH on G2
TE0842*






























I/O resource comparison for all 4x5 modules. There are maximum 4 user supplied I/O voltages (VCCIOA, VCCIOB, VCCIOC and VCCIOD).

*Attention: Maximum supply voltage for HP banks is 1.8V.

Module B2B FPGA-Banks and Voltages


Module Pinout Overview

Module basic power and group pin assignment, recommended to verify with Schematics


Carrier Board Power Connection Table

IO VoltageB2B Connector

Carrier Boards

NameDirection*JB1JB2TE0701TE0703 Rev01 - Rev04TE0703 Rev 05TE0705TE0706TEBA0841TEBA0841 REV01


PinPinSchematic NameValue,Option,Comp.Schematic NameValue,Option,Comp.Schematic NameValue,Option,Comp.Schematic NameValue,Option,Comp.Schematic NameValue,Option,Comp.Schematic NameValue,Option,Comp.Schematic NameValue,Option,Comp.
PWR_1out2,4,61,3,5,75V05V3.3V3.3V3.3V3.3V5V05V3.3V3.3V3.3Vuse ext. 3.3V power supply3.3Vuse ext. 3.3V power supply
VCCIOAout10,12
VIOTB

FMC_VADJ

2V5

3.3VOUT

VCCIO35

R23→M3.3VOUT

J1B-B1

VCCIOA

J5→M3.3VOUT, M1.8VOUT

R23→M3.3VOUT

J1-B1

VIOTB

FMC_VADJ

2V5

3.3VOUT

VCCIO35R20->M3.3VOUT/J6B-B32VCCIOA

J26→ M1.8VOUT, 2.5V, 3.3V_OUT

J20-6,J20-45

VCCIOAJ26→ M1.8VOUT, 2.5V, 3.3V_OUT
J20-6,J20-45
VCCIODout
8,10VIOTB

FMC_VADJ

2V5

3.3VOUT

VCCIO13

R26→M3.3VOUT

J2B-B1

VCCIOD

J10→M3.3VOUT, M1.8VOUT

R26→M3.3VOUT

J2B-B1

VIOTB

FMC_VADJ

2V5

3.3VOUT

VCCIO13R22->M3.3VOUT/J6B-B1VCCIOD

J27→ M1.8VOUT, 2.5V, 3.3V_OUT

J17-6,J17-45

VCCIOD

J27→ M1.8VOUT, 2.5V, 3.3V_OUT

J17-6,J17-45

PWR_2out14,16
3V3IN3.3V3.3V3.3V3.3V3.3V3V3IN3.3V3.3V3.3V3.3Vuse ext. 3.3V power supply3.3Vuse ext. 3.3V power supply
VCCIOBout
2,4no name / VIOTA

FMC_VADJ

2V5

3.3VOUT

VCCIO34

J5→M3.3VOUT

J1B-B32

VCCIOB

J8→M3.3VOUT,M1.8VOUT

J2B-B32

VIOTB

FMC_VADJ

2V5

3.3VOUT

1.8V1.8VVCCIOB

J5→ M1.8VOUT, 2.5V, 3.3V_OUT

VCCIOBNC
VCCIOCout
6no name / VIOTA

FMC_VADJ

2V5

3.3VOUT

VCCIO33

R25→M3.3VOUT

J2B-B32

VCCIOC

J9→M3.3VOUT, M1.8VOUT

R25→M3.3VOUT

J2B-B32

VIOTB

FMC_VADJ

2V5

3.3VOUT

VCCIO33R21->M3.3VOUTVCCIOCJ6→ M1.8VOUT, 2.5V, 3.3V_OUTVCCIOCNC
PWR_M1in
9,113.3VOUT3.3V3.3VOUT3.3VM3.3VOUT3.3V3.3VOUT3.3VM3.3VOUT3.3V3.3V_OUT3.3V3.3V_OUT3.3V
PWR_M2in40
VIOB1.8VM1.8VOUT1.8VM1.8VOUT1.8VVIOB1.8VM1.8VOUT1.8VM1.8VOUT1.8VM1.8VOUT1.8V
PWR_M3in
20NC
NC
NC
NC
NC

NC
NC
PWR_VBATout80
VBATB1VBATJ7VBATJ7NC
VBATJ9VBATNCVBATNC

PWR_JTAG

in
92VCCJTAG
VCCJTAG
VCCJTAG
VCCJTAG
VCCJTAG
VCCJTAG
VCCJTAGNC

Power comparison of all 4x5 carrier boards. *Power direction based on carrier boards view.There are 4 variable user supplied I/O voltages (VCCIOA, VCCIOB, VCCIOC and VCCIOD). PWR_1 and PWR_2 are fixed from carrier boards. PWR_M1 and PWR_M2 normally use default value from module. NC=Not Connected

Attention: On some carrier boards the user supplied I/O voltages are connected together (red colored schematic names).

Power Pin Connection on different Carrierboards

Carrier Pinout Overview

Carrierboard basic power and group pin assignment (Top View), recommended to verify with Schematics

4x5 Module Controller IOs

NameModule B2B PinCarrier B2B PinDirection (Module view)DescriptionRecommendation
JTAGSELJM1-89JB1-90inJTAG Chain multiplexer. Low FPGA, High CPLD.  For module with CPLD only.

Connect Pulldown on carrier.
DIP switch possible.

SC_EN1JM1-28JB1-27inModule power. Set high to enable module power. Note: Power management depends on module. Sometimes this is a only used as Power ON Reset like SC_nRSTConnect Pullup on carrier.
DIP switch possible
SC_NOSEQJM1-7JB1-8in / inoutModule Power management. Set high to disable CPLD power management. Note: Power management depends on module and not all modules support extended power management with CPLD.Connect Pullup or force to GND over zero ohm resistor on carrier.
DIP switch possible.
SC_PGOODJM1-30JB1-29out / inoutPower Good signal. Is Low, if SC_EN1 is set to zero or if power is not ready, otherwise high impedance output. Note:  Power management depends on module.
On newer Firmware SC_PGOOD will be used as Additionally Boot Mode Pin.
Connect Pullup on carrier.
Do not use this signal to enable FPGA Bank voltages. It's only for monitoring. To Enable FPGA Banks, use 3.3V(PWR_M1) or 1.8V(PWR_M2) module output. 
SC_BOOTMODEJM1-32JB1-31inBoot Mode selection Pin for Zynq module only. Default low for primary SD boot and high for primary QSPI boot. Note: Depends also on module CPLD firmwareConnect Pullup on carrier.
DIP switch possible.
SC_nRSTJM2-18JB2-17inLow active module reset. Pin force Power one reset on FPGA/SoC. Note: Depending from module CPLD or voltage supervisor is used.Connect Pullup on carrier.
DIP switch possible.
  • Controller IOs are 3.3V IOs


It's planned to use SC_PGOOD also as additional Boot Mode Pin (Pin is bidirectional, pull up or force to zero), to additionally set JTAG only boot mode (to avoid programming problems with some vivado versions, see: AR#00002 - QSPI Programming issues). Current state of CPLD Redesigns: AVN-20220506 4 x 5 modules controller IOs redefinition and CPLD updates

4x5 Module Controller IOs

Remove 4x5 module

4 x 5 SoMs Handling and Usage Precautions


Compatibility Guide

Ethernet LED'S

TE07xx 4x5 modules do not have dedicated pins for the Ethernet PHY LED's, also there are no fix pins on the baseboards for the PHY LED's or any other LED's.

If Ethernet JACKs on Baseboard have LED's then those should be connected to some free PL I/O pins, and then routed in the FPGA logic from the PHY to the I/O Pin in the B2B Connector.

Recommended connections would be to use JM2.89 and JM2.100 for the PHY LED's, those positions support baseboard ETH LED's for TE0701 and TE0703 and TE0706.

JM2 pins 1, 3 (TE0720 Bank 34 Voltage)

To be compatible with TE0720 JM2 pins 1,3 must be connected to some valid VCCIO voltage.

When JM2 pins 1, 3 are not powered TE0720 would not boot, and may not be recognized in JTAG chain as well.

When those pins are not used on the module (TE0710) then to be compatible with TE0720:

Solution A: connect to 3.3V out from the module, option compatible to all modules except those with HP banks

Solution B: connect to 1.8V out from the module, option compatible with all modules.

Carrier Board Checklist

Schematic Checklist




1Are B2B pin numbers on the connectors mirrored compared to the module pin numbers?As B2B connectors are "unisex" type the do mirror pin numbers when connecting. That is pin1 connects to pin2, and pin2 to pin1, etc.
2Are B2B connectors named JB1, JB2, JB3?This is not a hard requirement, but it helps to use the same identifiers.
3Are all GND pins connected to a common ground net?
4Are all VIN pins connected together?
5Is JB2 pin 92 pin used as VREF for the JTAG interface?for future compatibility only, currently all modules have 3.3V JTAG
6For 7 Series Zynq module only: Are external circuits/buffers connecting to MIO bank 1 pins powered from JB1 pin 40?JB1 pins 18, 20, 22, 24, 26, 28 use voltage at pin 40 as VCCIO. Currently it is 1.8V for 4x5 Zynq Modules.
Note: Different Power supply on TE0820(3.3V MIO Bank) and normal FPGA modules(check schematics) 

PCB Checklist




1

Are mounting holes placed properly?

Four Mounting holes should always be used. They are required for mounting screws and for module extraction. The mounting holes will also help in dissipating some heat from the module to the carried board PCB. Four holes with a 3.2mm diameter should be placed exactly at the corners of a 34mm by 44mm rectangle.
2Are B2B headers properly placed?B2B headers must be placed and aligned very precisely or the module will not align correctly (in the worst case module insertion could destroy the connectors or the PCB). The B2B headers should be locked on the PCB, and it is recommended that the position and placement be checked against placement dimensions before submitting the PCB files.
3Are B2B headers rotated properly?As B2B header pin numbers differ from module to the carrier (swap of odd and even numbers), it is recommended that the rotation is checked in the PCB design.
4Height clearance below moduleComponents can be placed below the module but height clearance rules must be obeyed.
5Power dissipation of components below moduleIt is not recommended to place any components with high power dissipation below the module, as there will be almost no airflow below the module.

Visual Check of Module placement

It is highly recommended to use the Base board Template designs as a starting point for new PCB designs. If that is not possible, then adding linear dimensions in the design helps to check that all connectors and mounting holes are properly placed.

This placement is same for all 4x5 Modules!


Top view of the Carrier Board.

Connector numbers as on base! (pin JB1.1 on base would mate to pin JM1.2 on module).




  • No labels