You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 8 Next »

Table of Contents

Overview

 

The Trenz Electronic TE0723-03 is a Arduino compatible FPGA module based on the Xilinx ZYNQ XC7Z010 SoC.

Block Diagram

Main Components

  1. Xilinx ZYNQ XC7Z010 SoC, U1
  2. 4 Gbit DDR3L 256M x 16 SDRAM, U2
  3. 16 MByte QSPI Flash memory, U5
  4. High-speed CMOS logic analog multiplexer/demultiplexer, U10

  5. 1 MHz low-power operational amplifier, U11
  6. Dual high-speed USB to multipurpose UART/FIFO, U3
  7. 0.5A dual channel current-limited power switch, U21
  8. Low-power programmable oscillator @ 12.000000 MHz, U7
  9. 2 Kbit Microwire compatible serial EEPROM, U6
  10. 10-pin header, J1
  11. 8-pin header, J2
  12. 10-pin header, J3
  13. Analog input header, J4
  14. 2 x 4 pin header, J5
  15. PMod 2x6 interface header, J6
  16. USB host mode jumper, J7
  17. Micro USB 2.0 Type-B receptacle, J8
  18. Micro USB 2.0 Type-B receptacle, J9
  19. Micro SD card connector with detect signal, J10
  20. Analog input select jumper, J11
  21. 5V supply power, J12
  22. Reset switch, S1
  23. Red LED, D2
  24. Green LED, D6
  25. Green LED, D7
  26. Ultra-low supply-current voltage monitor, U23
  27. 1A PowerSoC DC-DC converter (3.3 V), U20

  28. 1A PowerSoC DC-DC converter (1.8 V, U19
  29. 1A PowerSoC DC-DC converter (1.35 V), U16
  30. Hi-speed USB 2.0 ULPI transceiver, U18
  31. Low-power programmable oscillator @ 52.000000 MHz, U14
  32. 1A PowerSoC DC-DC converter (1.0 V), U17
  33. JTAG interface testpoints, TP1-TP4

Key Features

  • Xilinx ZYNQ XC7Z010 SoC
  • 16 MByte QSPI Flash
  • Dual ARM Cortex A9 processors
  • 512 MByte DDR3L SDRAM
  • Micro SD Card socket with card detect signal
  • ...

Additional assembly options are available for cost or performance optimization upon request.

Initial Delivery State

Storage device name

Content

Notes

QSPI Flash

Empty

 

Signals, Interfaces and Pins

I/O Signals

List of I/O signals between PS/PL banks and external connectors:

BankTypeConnectorSignal CountVoltageNotes
34HRJ163.3D8 .. 13, SDA, SCL
34HRJ283.3D2 .. 7, RXD, TXD
34HRJ683.3PIO01 .. PIO08
35HRJ473.3

AIN0 .. 5

35HRJ513.3ESP_GPIO2
500MIOJ1063.3SDCARD
501MIOJ543.3ESP_RXD, ESP_TXD, ESP_GPIO0, MOD_RST

JTAG Interface

JTAG access to the Xilinx ZYNQ XC7Z010 SoC is provided through testpoints TP1-T4.

JTAG Signal

Testpoint

TCK TP3
TDI TP1
TDO TP2
TMS TP4

LEDs

LEDColorConnected ToDescription and Notes
D2RedMIO9, U1 
D6

Green

Bank 34, U1FPGA_LED
D7

Green

3.3V

PWR_LED

Default PS MIO Mapping

MIOFunctionConnected ToNotes
0SDCARDJ10-9Card detect switch.
1QSPIU5-1SP0-CS
2QSPIU5-5SPI0-DQ0
3QSPIU5-2SPI0-DQ1
4QSPIU5-3SPI0-DQ2
5QSPIU5-7SPI0-DQ3
6QSPIU5-6SPI0-SCK
7GPIOU18-27USB PHY reset
9LEDD2Red LED
10SDCARDJ10-7DAT0
11SDCARDJ10-3CMD
12SDCARDJ10-5CLK
13SDCARDJ10-8DAT1
14SDCARDJ10-1DAT2
15SDCARDJ10-2CD/DAT3
28USB-OTGU18-7OTG-DATA4
29USB-OTGU18-31OTG-DIR
30USB-OTGU18-29OTG-STP
31USB-OTGU18-2OTG-NXT
32USB-OTGU18-3OTG-DATA0
33USB-OTGU18-4OTG-DATA1
34USB-OTGU18-5OTG-DATA2
35USB-OTGU18-6OTG-DATA3
36USB-OTGU18-1OTG-CLK
37USB-OTGU18-9OTG-DATA5
38USB-OTGU18-10OTG-DATA6
39USB-OTGU18-13OTG-DATA7
48ESPJ5-2ESP_TXD
49ESPJ5-7ESP_RXD
52ESPJ5-6MOD_RST
53ESPJ5-3ESP_GPIO0

I2C Interface

I2C interface pins from the ZYNQ SoC PL bank 34 are connected to the connector J1. There are no on-board I2C slave devices.

SignalZYNQ SoC PinConnected To
SDAR13J1-9
SCLP13J1-10

On-board Peripherals

Processing System (PS) Peripherals

NameICIDPS7MIONotes
SPI FlashS25FL127SABMFV10U5QSPI0MIO1 .. MIO6 
LED-D1GPIOMIO9 
USBUSB3320U18USB0MIO28 .. MIO39 
USB Reset-U18GPIOMIO7 

Clocking

Clock SignalFrequencyICSignal, Pin

Processing system (PS) reference clock.

52.000000 MHz

U1

PS_CLK, C7

USB transceiver reference clock.

52.000000 MHz

U18

OTG-RCLK, 26

High-speed USB to multipurpose UART/FIFO oscillator input.12.000000 MHzU3OSCI, 3

Power and Power-On Sequence

Power Supply

Single 5V power supply with minimum current capability of 2A for system startup is recommended.

Power Consumption

TBD - To Be Determined.

Power-On Sequence

There is no sequence...

Technical Specifications

Absolute Maximum Ratings

Parameter

MinMax

Units

Reference Document

VIN supply voltage

-0.53.6

V

Xilinx datasheet DS187, "Zynq-7000 All Programmable SoC: DC and AC Switching Characteristics".

Storage temperature

-40

+85

°C

 

Recommended Operating Conditions

ParameterMinMaxUnitsReference Document
Supply voltage1.143.465 VXilinx datasheet DS187, "Zynq-7000 All Programmable SoC: DC and AC Switching Characteristics".
Assembly variants for higher storage temperature range are available on request.

Physical Dimensions

  • Module size: 68.58 mm × 53.34 mm.  Please download the assembly diagram for exact numbers.

  • PCB thickness: 1.6 mm.

  • Highest part on PCB: approx. 4 mm. Please download the step model for exact numbers.

Please note that two different units are used on the figures below, SI system millimeters (mm) and imperial system thousandths of an inch(mil). To convert mils to millimeters and vice versa use formula 100mil's = 2,54mm.

Operating Temperature Ranges

Commercial grade: 0°C to +70°C.

Industrial grade: -40°C to +85°C.

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

Weight

... g - Plain module

... g - Set of bolts and nuts

Revision History

Hardware Revision History

DateRevision

Notes

PCNDocumentation Link
2016-07-1503 Click to see PCN.TE0723-03
2015-11-06
02  TE0723-02
 

01

 

  

Hardware revision number is printed on the PCB board together with the module model number separated by the dash.

Document Change History

Date

Revision

Contributors

Description

2017-02-11

Jan Kumann

Initial document.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3578#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • No labels