You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 14 Next »

Table of Contents

Overview

 

The Trenz Electronic TEBF0808 Carrier Board is a baseboard for the Xilinx Zynq Ultrascale+ MPSoC modules TE0808 and TE0803, which exposes the module's B2B connector pins to accessible connectors and provides a whole range of on-board components to test and evaluate the Zynq Ultrascale+ SoMs and for developing purposes.

Key Features

  • Mini-ITX form factor, PC Enclosure compatible
  • ATX power supply connector
  • Optional 12V standard power plug
  • Headers
    • Intel 10-pin HDA Audio
    • Intel 9-pin Power-/Reset-Button, Power-/HD-LED
    • PC-BEEPER
  • On-board Power- / Reset-Switches
  • 2x Configuration 4-bit DIP-switches
  • 2x Optional 4-wire PWM fan connectors
  • PCIe Slot - one PCIe lane (16 lane connector)
  • CAN FD Transceiver (10 Pin IDC connector and 6-pin header)
  • 4x On-board configuration EEPROMs (1x Microchip 24LC128-I/ST, 3x  Microchip 24AA025E48T-I/OT)
  • Dual SFP+ Connector (2x1 Cage)
  • One Display-Port (single lane)
  • One SATA Connector
  • 2x USB3.0 A Connector (Superspeed Host Port (Highspeed at USB2.0))
  • 1x USB3.0 on-board header with two ports
  • FMC HPC Slot (FMC_VADJ max. VCCIO)
  • FMC Fan
  • Gigabit Ethernet RGMII PHY with RJ45 MegJack
  • All Carrier Board peripherals' I²C-interfaces muxed to MPSoC's I²C-interface on PS bank 503
  • Quad programmable PLL clock generator SI5338A
  • 2x SMA coaxial connectors for clock signals
  • MicroSD- / MMC-Card Socket (bootable)
  • 32 Gbit on-board eMMC memory (8 banks a 4 Gbit)
  • Two System Controller CPLDs Lattice MachXO2 1200 HC
  • One Samtec FireFly (4 GT lanes bidirectional)
  • One Samtec FireFly connector for reverse loopback
  • 2x JTAG/UART header ('XMOD FTDI JTAG Adapter'-compatible) for programming MPSoC and SC CPLDs
  • 20 Pin ARM JTAG Connector (PS JTAG0)
  • 3x PMOD connector (GPIO's and I²C interface to SC CPLDs / MPSoC module
  • Carrier SC CPLD managing power-up sequence of MPSoC module
  • On-board DCDC PowerSoCs

Additional assembly options are available for cost or performance optimization upon request.

Block Diagram

Figure 1: TEBF0808-04 Block Diagram

Main Components

Figure 2: TEBF0808-04 Carrier Board

  1. PMOD connector, P2
  2. MicroSD Card socket (on bottom side), J16
  3. Display Port socket, J13
  4. USB3.0 A 2x , RJ45 1x (stacked), J7
  5. SFP+ 2x1 cage, J14
  6. PCIe x16 connector (one PCIe lane connected), J11
  7. FMC HPC, J5
  8. FMC-Fan connector 5V, J19
  9. USB3.0 connector, J8
  10. PC-BEEPER 4-pin header, J23
  11. SMA coaxial connector (SI5338A clock output), J32
  12. SMA coaxial connector (clock input to MPSoC module), J33
  13. eMMC Card socket, J27
  14. Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J4
  15. Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J1
  16. Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J3
  17. Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J2
  18. CAN bus 6-pin header, J29
  19. CAN bus 10-pin connector, J24
  20. ARM-JTAG  20-pin connector, J30
  21. ATX power supply connector, J20
  22. 4-Wire PWM fan connector, J35
  23. JTAG/UART header ('XMOD FTDI JTAG Adapter'-compatible) for access to MPSoC module, J12
  24. JTAG/UART header ('XMOD FTDI JTAG Adapter'-compatible) for access to System Controller CPLDs, J28
  25. Power Jack 2.1mm 12V, J25
  26. 4-bit DIP-switch, S5
  27. Power Button, S1
  28. Samtec FireFly Connector  for reverse loopback, J21/J22
  29. Samtec FireFly Connector (4 GT lanes bidirectional), J6/J15
  30. SATA Header, J31
  31. 4-Wire PWM fan connector, J26
  32. Programmable on-module PLL I²C interface 10-pin header, J17
  33. Reset Button, S2
  34. INTEL HDA 9-pin header, J9
  35. Intel front panel (PWR-/RST-Button, HD-/PWR-LED) 9-pin header, J10
  36. Samtec FireFly Connector J6/J15 I²C interface 3-pin header, J34
  37. 4-bit DIP-switch, S4
  38. PMOD connector, P3
  39. PMOD connector, P1
  40. Battery Holder CR1220, B1

Initial Delivery State

Storage device name

Content

Notes

General Purpose Configuration EEPROMs (1x Microchip 24LC128-I/ST, 3x Microchip 24AA025E48T-I/OT)

Not programmed

-
USB3.0 HUB Configuration EEPROM (Microchip 24LC128-I/ST)Not programmed-
Si5338A programmable PLL NVM OTPNot programmed-

Table 1: Initial Delivery State of the flash memories

Signals, Interfaces and Pins

FMC HPC Connector

The FMC (FPGA Mezzanine Card) connector J5 with high pin count (HPC) provides as an ANSI/VITA 57.1 standard a modular interface to the MPSoCs FPGA and exposes numerous of its I/O pins for use by other mezzanine modules and expansion cards.

The connector supports single ended (VCCIO: FMC_VADJ) and differential signaling as the I/O's are usable as LVDS-pairs.

The I/O signals are routed from the FPGA banks as LVDS-pairs to the connector.

Figure 2: FMC HPC Connector

FPGA BankI/O Signal CountLVDS-pairs countVCCO bank VoltageReference Clock Input from FMC ConnectorNotes
Bank 482010FMC_VADJ

1 reference clock signal from FMC connector
J5 (pins J5-G2, J5-G3) to bank's pins B48_L6_P / B48_L6_N

-
Bank 644623FMC_VADJ

1 reference clock signal from FMC connector
J5 (pins J5-H4, J5-H5) to bank's pins B64_L14_P / B64_L14_N

bank's VREF-pin connected to FMC connector pin J5-H1 (VREF_A_M2C)

Bank 654623FMC_VADJ-bank's VREF-pin connected to FMC connector pin J5-H1 (VREF_A_M2C)
Bank 664824FMC_VADJ-bank's VREF-pin connected to FMC connector pin J5-H1 (VREF_A_M2C)

Table 2: FMC connector pin-outs of available logic banks of the MPSoC

The MGT-banks have also clock input-pins which are exposed to the FMC connector. Following MGT-lanes are available on the FMC connectors J5:

GT BankTypeCount of MGT LanesSchematic Names / Connector PinsMGT Bank's Reference Clock Inputs from FMC Connector
228GTH4 GTH lanes

B228_RX3_P, B228_RX3_N, pins J5-A10, J5-A11
B228_TX3_P, B228_TX3_N, pins J5-A30, J5-A31

B228_RX2_P, B228_RX2_N, pins J5-A6, J5-A7
B228_TX2_P, B228_TX2_N, pins J5-A26, J5-A27

B228_RX1_P, B228_RX1_N, pins J5-A2, J5-A3
B228_TX1_P, B228_TX1_N, pins J5-A22, J5-A23

B228_RX0_P, B228_RX0_N, pins J5-C6, J5-C7
B228_TX0_P, B228_TX0_N, pins J5-C2, J5-C3

1 reference clock signal (B228_CLK0) from FMC connector
J5 (pins J5-D4, J5-D5) to MPSoC bank's pins R8/R7

229GTH4 GTH lanes

B229_RX3_P, B229_RX3_N, pins J5-B12, J5-B13
B229_TX3_P, B229_TX3_N, pins J5-B32, J5-B33

B229_RX2_P, B229_RX2_N, pins J5-B16, J5-B17
B229_TX2_P, B229_TX2_N, pins J5-B36, J5-B37

B229_RX1_P, B229_RX1_N, pins J5-A18, J5-A19
B229_TX1_P, B229_TX1_N, pins J5-A38, J5-A39

B229_RX0_P, B229_RX0_N, pins J5-A14, J5-A15
B229_TX0_P, B229_TX0_N, pins J5-A34, J5-A35

1 reference clock signal (B229_CLK0) from FMC connector
J5 (pins J5-B20, J5-B21) to MPSoC bank's pins L8/L7

230GTH2 GTH lanes

B230_RX1_P, B230_RX1_N, pins J5-B4, J5-B5
B230_TX1_P, B230_TX1_N, pins J5-B24, J5-B25

B230_RX0_P, B230_RX0_N, pins J5-B8, J5-B9
B230_TX0_P, B230_TX0_N, pins J5-B28, J5-B29

-

Table 2: FMC connector pin-outs of available MGT-lanes of the MPSoC

The FMC connector provides pins for reference clock output to the Mezzanine module and clock input to PL banks of the MPSoC:

Clock Signal Schematic Name
FMC Connector PinsDirectionClock SourceNotes
B228_CLK0J5-D4 / J5-D5inFMC Connector J5clock signal to MGT bank 228
B229_CLK0J5-B20 / J5-B21inFMC Connector J5clock signal to MGT bank 229
FMCCLK2J5-K4 / J5-K5outCarrier Board PLL SI5338A U35, CLK2-
FMCCLK3J5-J2 / J5-J3outCarrier Board PLL SI5338A U35, CLK3-
B64_L14_P / B64_L14_NJ5-H4 / J5-H5inFMC Connector J5bank 64 clock capable pin-pair
B48_L6_P / B48_L6_NJ5-G2 / J5-G3inFMC Connector J5bank 48 clock capable pin-pair

Table 3: FMC connector pin-outs for reference clock output

The FMC connector provides further interfaces like 'JTAG' and 'I²C' to the System Controller CPLD:

Interfaces I/O Signal CountPin schematic Names / FMC PinsConnected toNotes
JTAG5

FMC_TCK, pin J5-D29

FMC_TMS, pin J5-D33

FMC_TDI, pin J5-D30

FMC_TDO, pin J5- D31

SC CPLD U17, bank 1

VCCIO: 3V3SB

TRST_L, pin J5-D34 pulled-up to 3V3_PER

I²C2

FMC_SCL, pin J5-C30

FMC_SDA, pin J5-C31

I²C-Switch U16

I²C-lines pulled-up to 3V3_PER

Control Lines3

FMC_PRSNT_M2C, pin J5-H2

FMC_PG_C2M, pin J5-D1 (3V3_PER pull-up)

FMC_PG_M2C, pin J5-F1 (3V3_PER pull-up)

FMC_CLK_DIR, pin J5-B1 (pulled-down to GND)

I²C-Switch U16 via I²C-I/O-Port-Expander U38

SC CPLD U39, bank 0

I²C-Switch U16 via I²C-I/O-Port-Expander U38

SC CPLD U17, bank 1

'PG' = 'Power Good'-signal

'C2M' = carrier to (mezzanine) module

'M2C' = (mezzanine) module to carrier

Table 4: FMC connector pin-outs of available interfaces to the System Controller CPLD

Several VCCIO voltages are available on the FMC connector to operate the I/O's in order of the intended purpose:

VCCIO Schematic NameFMC Connector J5 PinsNotes
12VC35/C37extern 12V power supply
3V3_PERD32/D36/D38/D40/C393.3V peripheral supply voltage
FMC_VADJH40/G39/F40/E39adjustable FMC VCCIO voltage, supplied by DCDC converter U8

Table 5:  Available VCCIO voltages on FMC connector

USB3.0 Interface

The TEBF0808 Carrier Board offers up to 4 USB3.0 superspeed ports, which are also downward compatible to USB2.0 highspeed ports. The USB3.0 ports are provided by the IC U4, Cypress Semiconductor CYUSB3324 4-port USB3.0 Hub. The pin-strap configuration option of the USB3.0 Hub U4 is disabled, so the Hub will only be configurable over the configuration EEPROM U5. The I²C interface of the EEPROM is also accessible by the MPSoC through I²C switch U16.

On the Upstream-side, this chip is connected to the MGT1-lane of MPSoC's PG GT bank 505 to establish the USB3.0 lane. For the USB2.0 interface, the USB3.0 HUB U4 is connected to the on-board USB2.0 PHY U9. The USB2.0 PHY U9 is connected per ULPI interface through MIO pins 52..63 to MPSoC's MIO bank 501.

Following block-diagram clarifies the wiring of the USB interface with the MPSoC.

 

Figure 3: TEBF0808 USB3.0 interface

MPSoC's PS GT Bank 505 Peripheral Interfaces

On the PS GT Bank 505 is beside the USB3.0 Lane also the interface SATA, Display-Port and PCI Express connected.

Figure 4: TEBF0808 USB3.0 interface

MGT Interfaces SFP+ and Firefly

 

  • No labels