You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 18 Next »

This Trenz Electronic Starter Kit consists of a TE0803 module on a TEBF0808 base board in Mini-ITX Enclosure. See shop link for detailed content.

Xilinx Software and Driver

Important Notes

Do not change XMOD DIP-Switch settings on TEBF0808. Do not swap the XMOD adapters the one marked with green dot must be closer to the SoM

ES devices are not included in all Vivado versions, for ES1 only:

activate beta device see: FAQ - How can I activate beta devices?

For all Starter Kit's shipped before 2017-06-21:

Enclosure Power and HD LED was swapped on connector. See "Enclosure Power Button, Reset Button, HDD LEDand Power LED" section for correct connection.

Getting Started

Starter Kit is shipped with prebuilt Linux Example on SD. Newest version and sources are available on our download area: TE0803 Reference Designs

  1. Connect main power and set power switch to on. See Main Power Enclosure Location

  2. Connect mini USB cable from XMOD with green dot to host PC. See XMODs Connection
  3. Insert SD-Card with pre-loaded content into SD-Card slot.
  4. Open Serial Console:
    1. COM Port: for correct number see device manager
    2. Speed:115200
  5. Press the Power on button on the enclosure. See Power Button, Reset Button, HDD LED and Power LED Enclosure Location
  6. Linux login:
    1. User Name:root
    2. Password:root

Starter Kit Basic

Main Power Enclosure Location

Power Button , Reset Button, HDD LED and Power LED Enclosure  Location

 

 Do not change XMOD DIP-Switch settings on TEBF0808. Do not swap the XMOD adapters the one marked with green dot must be closer to the SoM
TEBF0808

TE0790-02

(with green dot)

TE0790-02L
DIP-SchalterS4
S4.1OFF
S4.2OFF
S4.3OFF
S4.4ON
DIP-SchalterS5
S5.1ON
S5.2ON
S5.3OFF
S5.4OFF
 DIP-SchalterS1
S1.1ON
S1.2OFF
S1.3OFF
S1.4OFF
 DIP-SchalterS1
S1.1ON
S1.2OFF
S1.3OFF
S1.4OFF

- Section is currently not complete -

Main Power Switch is OFF

No Power on Starter Kit.

Identification: FANs do not work, all LEDs are off.

Main Power Switch is ON and Power Button is not pressed

Only some basics on TEBF0808 are powered on. This mode is used for CPLDs Firmware updates.

Identification: FANs do not work, some LEDs blinking.

LED description (need CPLD Firmware REV06 or newer):

BLUE Power LED  on enclosure
Status/ UserBlink SequenceComment
Power******** (slow blink)

Indicate board is powered off.

RGPIO controlledUser Defined

RGPIO 14 and 15, if RGPIO is active.

MIO40User Defined

MIO40, if RGPIO is deactivated

Main Power Switch is ON and Power Button is pressed first time

TE0803 will be powered on. System boots, if boot mode is set correct and files are available.

Identification: FANs do work, LEDs blinking states change.

LED description(need CPLD Firmware REV06 or newer):

BLUE Power LED  on enclosure
Status/ UserBlink SequenceComment
Power******** (slow blink)

Indicate board is powered off.

RGPIO controlledUser Defined

RGPIO 14 and 15, if RGPIO is active.

MIO40User Defined

MIO40, if RGPIO is deactivated

Red HD LED  on enclosure
Status/ UserBlink SequenceComment
PS_INIT_B********

Indicates the PS is not initialized after a power-on reset (POR).

PS_ERROR_OUT*****ooo

The PS_ERROR_OUT signal is asserted for accidental loss of power, an error, or an exception in the PMU.

ERR_STAT****oooo

The PS_ERROR_STATUS indicates a secure lockdown state. Alternatively, it can be used by the PMU firmware to indicate system status.

RGPIO controlledUser Defined

RGPIO 16 and 17, if RGPIO is active

SC0User DefinedSC0 (PL IO), if RGPIO is deactivated

Notes

Starter Kit will be shipped with all cable connected.

ATX Power

Module

FMC FAN

XMODs

Enclosure USB

Enclosure FAN1 and HDAUDIO

Enclosure Power Button , Reset Button, HDD LED and Power LED

Support

  • No labels