You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 7 Next »

Download PDF version of this document.

Table of Contents

Overview

The Trenz Electronic TEB0835 is a carrier for TE0835 module which is based on Xilinx UltraScale+ RFSoC.

Refer to http://trenz.org/teb0835-info for the current online version of this manual and other available documentation.

Key Features

  • Modules: 
    • TE0835
  • RAM/Storage
    • 4K EEPROM
  • On Board
    • Programmable Clock Generator
    • I2C Switch IC
    • 9x Green LEDs
    • 16x RF Transformation
    • Reset Push Buttons
    • SDIO Port Expander
    • DIP Switch
  • Interface
    • 10x U.FL Series Connectors
    • 6x SMA Connectors
    • Micro USB2.0
    • 2x UEC5 Connectors
    • 2x UCC8 Connectors
    • PCIe 8x Connector
    • 2x Samtec Razor Beam SS5 (2x80 pol) Board to Board Connectors
  • Power
    • 5V Input Supply Voltage
  • Dimension
    • 106.6 mm  x 167.6 mm


Block Diagram

TEB0835 block diagram

Main Components

TEB0835 main components
  1. SMA Connectors, J1,J3,J5,J7,J9,J11
  2. U.FL (UMCC) Connectors, J2,J4,J6,J8, J10, J12...16
  3. Green LEDs, D6...11
  4. B2B Connector, J18
  5. B2B Connector, J17
  6. Micro SD Card Connector, J28
  7. Reset Push Button, BTN1
  8. Mosfet Transistors
  9. PCIe Connector, J19
  10. Micro USB2.0 Connectors, J29-J30
  11. Gigabit RJ45 Connector, J31
  12. DIP Switch, S1
  13. UEC5 Connector, J22,J24
  14. UCC8 Connector, J23,J25
  15. 4x1 Pin Header, J21
  16. FTDI, U12
  17. Green LEDs, D1...3
  18. 4x1 Pin Header, J20
  19. EEPROM, U15
  20. PCIe Card, J26

Initial Delivery State

Storage device name

Content

Notes

EEPROMProgrammed
Initial delivery state of programmable devices on the module

Configuration Signals

MODE Signal State

|Boot Mode





MODE[0:3]

Boot ModePin LocationNote

0000

PS_JTAG

JTAGPSJTAG Interface
0001Quad SPI (24b)MIO0...12QSPI 24bit addressing
0010Quad SPI (32b)MIO0...12QSPI 32bit addressing
0011SD0 2.0MIO13...25SD 2.0
0100NANDMIO9...25Requires 8 bit data bus width
0101SD1 2.0MIO31...51SD 2.0
0110eMMCMIO13...22eMMC version 4.5 at 1.8 V
0111USB2.0MIO52...63Only USB2.0
1000PJTAGMIO26...29PJTAG Connection 0 0ption
1001PJTAGMIO12...15PJTAG Connection 1 0ption
1110SD1 LS 3.0MIO39...51SD 3.0 with complaint voltage level shifter
Boot process.

Signal

B2BI/ONote

RESETN

J17- 36InputConnected to Push Button, BTN1
Reset process.

Signals, Interfaces and Pins

Board to Board (B2B) I/Os

FPGA bank number and number of I/O signals connected to the B2B connector:

FPGA BankB2B ConnectorI/O Signal CountVoltage LevelNotes
Bank 500J1712x Single Ended1.8VMIO14...25
Bank 501J1720x Single Ended1.8VMIO26...51
Bank 505J1718x Single Ended, 9x Differential pairs0.85VEXT_CLKIN_PSMGT, RX/TX0...3
Bank 128J1718x Single Ended, 9x Differential pairs0.9VB128_CLK, RX/TX0...3
Bank 129J1718x Single Ended, 9x Differential pairs0.9VB129_CLK, RX/TX0...3
Bank 65J1824x Single Ended, 12x Differential pairs1.8V
Bank 88J1816x Single Ended, 8x Differential pairs3.3VHD_B88
General PL I/O to B2B connectors information

JTAG Interface

JTAG access to the TEB0835 SoM through B2B connector J17.

JTAG Signal

B2B Connector

TMSJ17-24
TDIJ17-20
TDOJ17-18
TCK

J17-22

JTAG pins connection

Ethernet

U?? Pin Signal NameConnected toSignal DescriptionNote






































































Ethernet PHY to Zynq SoC connections

Micro USB2.0

U?? Pin Signal NameConnected toSignal DescriptionNote






































































Micro USB2.0 Socket connections

SMA Connectors

U?? Pin Signal NameConnected toSignal DescriptionNote






































































SMA Connectors information

UMCC Connectors

U?? Pin Signal NameConnected toSignal DescriptionNote






































































UMCC Connectors

UCE5 Connectors

U?? Pin Signal NameConnected toSignal DescriptionNote






































































UEC5 Connectors

UCC8 Connectors

U?? Pin Signal NameConnected toSignal DescriptionNote






































































UCC8 Connectors

PCIe Card

U?? Pin Signal NameConnected toSignal DescriptionNote






































































PCIe-x8-Kurz Connectors

MIO Pins


MIO PinConnected toB2BNotes
MIO0...12SPI FLash, U24-U25-Dual SPI FLash
MIO13LED Green, D1-3.3V_CPLD
MIO14...25FPGA Bank 500,U1J1PSMIO
MIO26...27FPGA Bank 501,U1J1PSMIO
MIO28...29CPLD, U31-

UART_TX, UART_RX

MIO30...31FPGA Bank 501, U1J1PSMIO
MIO32...33EEPROM,U23-I2C_SCL, I2C_SDA
MIO34...35FPGA Bank 501,U1J1PSMIO
MIO36Gigabit ETH, U20-ETH_RST
MIO37USB2.0, U11-USB_RST
MIO38...51FPGA Bank 501, U1J1PSMIO
MIO52...62USB2.0, U11-USB
MIO63...77Gigabit ETH, U20-ETH
MIOs pins

Test Points

Test PointSignalConnected toNotes
TP15VB2B, J17
TP2...3GNDGND
TP4ADC0_VCMB2B, J18
TP5ADC1_VCMB2B, J18
TP6USB_VBUSMicro USB2.0, J29
TP7UART0_RXB2B, J17
TP8UART0_TXB2B, J17
TP9ADC2_VCMB2B, J18
TP10ADC3_VCMB2B, J18
TP11ADC4_VCMB2B, J18
TP12ADC5_VCMB2B, J18
TP13ADC6_VCMB2B, J18
TP14ADC7_VCMB2B, J18
Test Points Information

On-board Peripherals

Chip/InterfaceDesignatorNotes
EEPROMU15
FTDIU12
LEDsD1...11
OscillatorsU16, U6
PLL Clock  GeneratorU5
On board peripherals


EEPROM

MIO PinSchematicU15 PinNotes








I2C EEPROM interface MIOs and pins

MIO PinI2C AddressDesignatorNotes




I2C address for EEPROM

LEDs

DesignatorColorConnected toActive LevelNote
D1GreenPG_1.8VHigh
D2GreenPG_3.3VHigh
D3GreenPG_5VHigh
D6...11GreenB2B, J18High
On-board LEDs

Clock Sources

DesignatorDescriptionFrequencyNote
U6MEMS Oscillator25MHz
U16MEMS Oscillator12MHz
U5PLL Clock GeneratorVariable
Osillators

Programmable Clock Generator

There is a programmable clock generator on-board (U??) provided in order to generate variable clocks for the module. Programming can be done using I2C via PIN header J??.  The I2C Address is 0x??.

U?? Pin
SignalConnected toDirectionNote
IN3CLK_25MHZ_ROscillator, U6Input
SCLPLL_SCLB2B, J17Input
SDAPLL_SDAB2B, J17In/Out
INTRPLL_INTR_NB2B, J17Output
CLK1B129_CLK1B2B, J17Output
CLK2B128_CLK1B2B, J17Output
Programmable Clock Generator Inputs and Outputs

Power and Power-On Sequence

Power Supply

Power supply with minimum current capability of 3 A for system startup is recommended.

Power Consumption

Power Input PinTypical Current
VINTBD*
Power Consumption

* TBD - To Be Determined

Power Distribution Dependencies

Power Distribution

Power-On Sequence

Create DrawIO object here: Attention if you copy from other page, objects are only linked.

Power Sequency

Voltage Monitor Circuit

Create DrawIO object here: Attention if you copy from other page, objects are only linked.

Voltage Monitor Circuit

Power Rails

Power Rail Name

B2B Connector

JM1 Pin

B2B Connector

JM2 Pin

B2B Connector

JM3 Pin

DirectionNotes
























Module power rails.

Bank Voltages

Bank          

Schematic Name

Voltage

Notes




























Zynq SoC bank voltages.


Board to Board Connectors

The TE0835 has two Samtec Razor Beam on the bottom side.

The module has three 160-pin double-row REF-192552-02 connector on the bottom side. The counterpart REF-192552-01 is placed on the base board.

Order
number

REF NumberSamtec NumberTypeMated HeightData sheetComment
27220REF-192552-02ST5-80-1.50-L-D-P-TRModule connector5 mmhttp://suddendocs.samtec.com/catalog_english/st5.pdfStandard connector
used on module
27219REF-192552-01SS5-80-3.50-L-D-K-TRBaseboard connector5 mmhttp://suddendocs.samtec.com/catalog_english/ss5.pdfStandard connector
used on board
Connectors.

 With different connectors from the used series other mating heights are possible (according to the Datasheet). The module and base board can be manufactured using other connectors upon request.

Connector SpecificationsValue
Insulator materialLiquid crystal polymer
Stacking height5 mm
Contact materialPhosphor-bronze
PlatingAu or Sn over 50 μ" (1.27 μm) Ni
Current rating1.6 A per pin (2 pins powered)
Operating temperature range-55 °C to +125 °C
RoHS compliantYes
Connector specifications.
Connector Speed Ratings

The LSHM connector speed rating depends on the stacking height; please see the following table:

Stacking heightSpeed rating
5 mm, Single-Ended 13.5GHz /  27Gbps
5 mm, Differential 20GHz / 40Gbps
4 mm, Single-Ended 13GHz /  26Gbps
4 mm, Differential 13.5GHz / 27Gbps
Speed rating.
Current Rating

Current rating of  Samtec Razor Beam™ SS5/ST5 B2B connectors is 1.6A per pin (2 pins powered).

Connector Mechanical Ratings
  • Shock: 100G, 6 ms sawtooth wave
  • Vibration: 7.56G 'RMS', 2 hours per axis, 3 axes total
Manufacturer Documentation

  File Modified
PDF File hsc-report-sma_st5-ss5-04mm_web.pdf 07 06, 2019 by John Hartfiel
PDF File hsc-report-sma_st5-ss5-05mm_web.pdf 07 06, 2019 by John Hartfiel
PDF File ss5_catalog.pdf 07 06, 2019 by John Hartfiel
PDF File ss5-st5_specs.pdf 07 06, 2019 by John Hartfiel



Technical Specifications

Absolute Maximum Ratings

SymbolsDescriptionMinMaxUnit




V




V




°C




°C
PS absolute maximum ratings

Recommended Operating Conditions

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

ParameterMinMaxUnitsReference Document



VSee ???? datasheets.



VSee Xilinx ???? datasheet.



VSee Xilinx ???? datasheet.



VSee Xilinx ???? datasheet.



VSee Xilinx ???? datasheet.



VSee Xilinx ???? datasheet.



VSee Xilinx ???? datasheet.



°CSee Xilinx ???? datasheet.



°CSee Xilinx ???? datasheet.
Recommended operating conditions.

Physical Dimensions

  • Module size: 106.6 mm × 167.7 mm.  Please download the assembly diagram for exact numbers.

  • Mating height with standard connectors: 5 mm.

PCB thickness: 1.5 mm.

Physical Dimension

Currently Offered Variants 

Trenz shop TEB0835 overview page
English pageGerman page
Trenz Electronic Shop Overview

Revision History

Hardware Revision History


DateRevisionChangesDocumentation Link
2019-11-29REV01Initial ReleaseREV01
Hardware Revision History

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Board hardware revision number.

Document Change History

DateRevisionContributorDescription

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • change list

--

all

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • --
Document change history.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]



  • No labels