You are viewing an old version of this page. View the current version.
Compare with Current
View Page History
« Previous
Version 12
Next »
TEBF0808 with TE080x
Overview
Basic instructions to work with TEBF0808 and TE0808,TE0807 or TE0803.
Number | Note |
| Letter | Note |
---|
1 | S2- Reset Button |
| A | P1 - PMOD 3.3V I2C Bus |
---|
2 | D7 - LED D7 Red (Usage: status) || D6 - LED Green (Usage: status) |
| B | J9 - Audio Enclosure |
---|
3 | S1 - Power Button |
| C | J26 - FAN1 12V |
---|
4 | J25 - Power Jack J25, 2.1mm (optional 12V power input) |
| D | J17 - I2C (for optional module PLL access) |
---|
5 | S5 - DIP Switch for Boot Mode and FMCVADJ |
| E | J6/15 - Firefly - GTH |
---|
6 | J10 - Enclosure Pin header(Reset and Power Button, HD LED (Usage: status/user) and Power LED (Usage: status/user)) |
| F | J31 - SATA |
---|
7 | S4 - DIP Switch for CPLD access and power control |
| G | J21/22 - Firefly - loopback only |
---|
8 | J12 - XMOD with green dot for Module JTAG and UART, XMOD LED D4 Red used for status information |
| H | P3 - PMOD 3.3V I2C Bus |
---|
9 | J28 - XMOD for CPLD,FMC JTAG and Firmware ID over UART(need CPLD Firmware 7 or newer) , XMOD LED D4 Red used for status information |
| I | J34 - I2C Firefly |
---|
10 | FPGA Done LED (location varies slightly on different module series ) |
| J | J35 - FAN2 12V |
---|
11 | J20 - ATX Power Connector (Main 12V and 5V Power supply), recommended power supply connector |
| K | J11 - PCIe (1x) |
---|
12 | D1 - SFP LED Red (Usage: status/user) |
| L | B1 - Battery holder CR1220 |
---|
13 | D8 - SFP LED Green (Usage: status/user) |
| M | J30 - PJTAG |
---|
14 | D9 - SFP LED Red (Usage: status/user) |
| N | J29 - CAN (same as J24) |
---|
15 | D10 - SFP LED Green (Usage: status/user) |
| O | J5 - FMC HPC |
---|
16 | J7 - ETH LED Yellow (Usage: status) |
| P | J19 - FAN3 5V |
---|
17 | J7 - ETH LED Green/Orange (Usage: status) |
| Q | J24 - CAN (same as J29) |
---|
18 | D4 - LED Green (Usage: status/user) || D5 - LED Red (Usage: status/user) |
| R | J27 - SD |
---|
--- | --- |
| S | J8 - USB 3.0 (2x) Enclosure |
---|
--- | --- |
| T | J14 - SFP (2x) |
---|
--- | --- |
| U | J7 - USB 3.0 (2x), ETH (1x) |
---|
--- | --- |
| V | J13 - Displayport (1x) |
---|
--- | --- |
| W | P2 - PMOD 3.3V FPG IOs |
---|
--- | --- |
| W(b) | Bottom side: J16 - microSD |
---|
Power supply
Label | Designator | Power | Description |
---|
Overview - 12 | J20 | 12V and 5V | Recommended power supply unit is PC power supply unit:- DIP S4-4 can be switched OFF with this power supply configuration (CPLD firmware depended)
|
Overview - 4 | J25 | 12V | Optional single 12V power supply: DIP S4-4 must be switched ON with this power supply |
Current depends manly on design and cooling solution. Use Xilinx Power Estimator and/or Your Vivado Project to estimate min current. Minimum of 3A are recommanded for basic functionality.
LEDs
Priority | Description | Blink sequencing |
---|
1 | 2 | 3 |
Furthermore, there are two user LEDs on module TE0728.
JTAG/UART
Label | Designator | Description |
---|
Overview - 8 | J12 | - SoC JTAG/UART over USB, UART Speed depends on design, normally 15200
- XMOD with Xilinx Licence (green dot)
|
Overview - 9 | J28 | - CPLD and FMC JTAG
- Press Button to see Firmware ID over UART (need CPLD Firmware 7 or newer), UART Speed 115200
|
DIP Switch on the XMOD JTAG adapter must be set like the following table.
For more information refer to TE0790.
CPLD Firmware
Firmware Update Instruction and CPLD description is available on TEBF0808 CPLD Firmware. Source code of the firmware is available on the download area of the TEBF0808.
Firmware Versions and some statistics can be displayed over second XMOD:
- Included since CPLD Firmware Update to REV07
- UART Speed is 115200
- Press XMOD Button to see output, otherwise RX/TX are loop backed
Reference Designs
Notes
Module and Carrier are also as starter kit available: