Download PDF version of this document.

Overview

The Trenz Electronic TE0818 is an industrial grade MPSoC SOM integrating an AMD Zynq UltraScale+ MPSoC, DDR4 SDRAM with 64-Bit width data bus connection, SPI Boot Flash memory for configuration and operation, transceivers and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/Os is provided via rugged high-speed stacking connections in a compact 5.2 cm x 7.6 cm form factor.

Refer to http://trenz.org/te0818-info for the current online version of this manual and other available documentation.

Key Features

  • SoC
    • Device: ZU6 / ZU9 / ZU15 1)
    • Engine: CG / EG  1)
    • Speedgrade: -1 / -2  1)
    • Temperature Range: Extended / Industrial 1)
    • Package: FFVC900
  • RAM/Storage
    • 4 GByte DDR4 SDRAM 2)
    • 2 x 64 MByte Serial Flash 3)
    • EEPROM with MAC address
  • On Board
    • Oscillator
  • Interface
    • 4 x B2B Connector (ADM6)
      • up to 204 PL IO

        • HP: 156
        • HD: 48
      • up to 65 PS MIO

      • 4 GTR
      • 16 GTH
      • I2C, JTAG, CONFIG
  • Power
    • 3.3 V power supply via B2B Connector needed 4).
  • Dimension
    • 76 mm x 52 mm
  • Notes
    1) Please, take care of the possible assembly options. Furthermore, check whether the power supply is powerful enough for your FPGA design.
    2) Up to 32 GByte are possible with a maximum bandwidth of 2400 MBit/s.
    3) Please, take care of the possible assembly options.
    4) Dependent on the assembly option a higher input voltage may be possible


TE0818 block diagram

Main Components

TExxxx main components
  1. SoC, U1
  2. DDR4, U2, U3, U9, U12
  3. Quad SPI Flash, U7, U17
  4. Connector, J1, J2, J3, J4
  5. EEPROM, U4
  6. Clock Generator, U5
  7. Oscillator, U25, U32

Initial Delivery State

Storage device name

Content

Notes

DDR4 SDRAMnot programmed
Quad SPI Flashnot programmed
EEPROMnot programmed besides factory programmed MAC address
Programmable Clock Generatornot programmed
Initial delivery state of programmable devices on the module

Signals, Interfaces and Pins

Connectors

Connector TypeDesignatorInterfaceIO CNTNotes
B2BJ1MGT PL12 x MGT (RX/TX)
B2BJ1HP52 SE / 24 DIFF
B2BJ2MGT PS2 x MGT CLK
B2BJ2CLKDIFF CLK
B2BJ2MGT PL4 x MGT (RX/TX)
B2BJ2MGT PS4 x MGT (RX/TX)
B2BJ2CFGJTAG
B2BJ2CFGMODE
B2BJ3HD48 SE / 24 DIFF
B2BJ3MGT PL3 x MGT CLK
B2BJ3CLKDIFF CLK
B2BJ3MIO65 GPIO
B2BJ4HP104 SE / 48 DIFF
Board Connectors


Test Points

Test PointSignalNotesRevision Notes
TP1PLL_SCLpulled-up to PS_1V8
TP2PLL_SDApulled-up to PS_1V8
TP3LP_DCDC

TP4DCDCIN

TP5GND

TP6TCK

TP7PL_DCIN

TP8GND

TP9GT_DCDC

TP10GND

TP11TDI

TP12TDO

TP13TMS

TP14PS_1V8

TP151V25_REFREF3312AIDCKT (U33) ouput voltageNo Net Name for REV01.
TP16FP_0V85

TP17DDR_2V5

TP18DDR_PLL

TP19PL_VCCINT

TP20AUX_R

TP21AVTT_R

TP22AUX_L

TP23DDR4-TEN
Only REV02.
TP24AVCC_R

TP25PLL_SDApulled-up to PS_1V8Only REV02.
TP26AVTT_L

TP27PLL_SCLpulled-up to PS_1V8Only REV02.
TP28AVCC_L

TP29LP_DCDC
Only REV02.
TP30PS_PLL

TP31PS_AVTT

TP32LP_0V85

TP33PS_AUX

TP34PS_AVCC

TP35DCDCIN
Only REV02.
TP36POR_B

TP37PL_DCIN
Only REV02.
TP38GT_DCDC
Only REV02.
TP39PS_1V8
Only REV02.
TP401V25_REF
Only REV02.
TP41FP_0V85
Only REV02.
TP42DDR_2V5
Only REV02.
TP43DDR_PLL
Only REV02.
TP44PL_VCCINT
Only REV02.
TP45AUX_R
Only REV02.
TP46AVTT_R
Only REV02.
TP47AUX_L
Only REV02.
TP48AVCC_R
Only REV02.
TP49AVTT_L
Only REV02.
TP50AVCC_L
Only REV02.
TP51PS_PLL
Only REV02.
TP52PS_AVTT
Only REV02.
TP53LP_0V85
Only REV02.
TP54PS_AUX
Only REV02.
TP55PS_AVCC
Only REV02.
TP56DDR_1V2
Only REV02.
TP57DDR_1V2
Only REV02.
TP58SI_PLL_1V8
Only REV02.
TP59SI_PLL_1V8
Only REV02.
TP60PL_GT2_1V35
Only REV02.
TP61PL_GT2_1V35
Only REV02.
TP62PL_GT2_1V05
Only REV02.
TP63PL_GT2_1V05
Only REV02.
TP64PL_GT_1V35
Only REV02.
TP65PL_GT_1V35
Only REV02.
TP66PL_GT_1V05
Only REV02.
TP67PL_GT_1V05
Only REV02.
TP683.3VIN
Only REV02.
TP693.3VIN
Only REV02.
TP70DCDC_2V0
Only REV02.
TP71DCDC_2V0
Only REV02.
TP72PS_GT_1V0
Only REV02.
TP73PS_GT_1V0
Only REV02.
TP74PL_1V8
Only REV02.
TP75PL_1V8
Only REV02.
TP76VREFA
Only REV02.
TP77VREFA
Only REV02.
TP78VTT
Only REV02.
TP79VTT
Only REV02.
Test Points Information

On-board Peripherals

Chip/InterfaceDesignatorConnected ToNotes

DDR4 SDRAM

U2, U3, U9, U12SoC - PS

Quad SPI Flash

U7, U17SoC - PSBooting.

EEPROM

U4B2B - J2

Clock Generator

U5SoC, B2B

Oscillator

U25Clock Generator25 MHz

Oscillator

U32SoC33.333333 MHz
On board peripherals

Configuration and System Control Signals

Connector+Pin

Signal Name

Direction1)Description
J1.A45POR_OVERRIDEINOverride power-on reset delay 2).
J2.A30PG_PLL_1V8OUTSI_PLL_1V8 power rail powered-up.
J2.A31ERR_OUTOUTPS error indication 2).
J2.A34ERR_STATUSOUTPS error status 2).
J2.A35LP_GOODOUTLow-power domain powered-up. Pulled up to 3.3VIN.
J2.A36PLL_SCLINI2C clock. Pulled up to PS_1V8.
J2.A37PLL_SDAIN/OUTI2C data. Pulled up to PS_1V8.
J2.A40PG_GT_LOUTLeft GTH Transceivers powered-up.
J2.A41EN_PSGTINEnable GTR transceiver power-up.
J2.A44 / J2.A45 /
J2.A46 / J2.A47
TCK / TDI / TDO / TMSSignal-dependent

JTAG configuration and debugging interface.

JTAG reference voltage: PS_1V8

J2.B29PG_PSGTOUTGTR transceivers powered-up.
J2.B30PROG_BIN/OUTPower-on reset 2). Pulled-up to PS_1V8.
J2.B33SRST_BINSystem reset 2). Pulled-up to PS_1V8.
J2.B34INIT_BIN/OUTInitialization completion indicator after POR 2). Pulled-up to PS_1V8.
J2.B37PG_PLOUTProgrammable logic powered-up.
J2.B38EN_FPDINEnable full-power domain power-up.
J2.B41PG_FPDOUTFull-power domain powered-up.
J2.B42EN_LPDINEnable low-power domain power-up.
J2.B45PG_DDROUTDDR power supply powered-up.
J2.B46DONEOUTPS done signal 2). Pulled-up to PS_1V8.
J2.B47EN_DDRINEnable DDR power-up.
J2.C30EN_GT_LINEnable left GTH transceiver power-up.
J2.C31MRINManual reset.
J2.C32PLL_SEL0INPLL clock selection.
J2.C33PLL_RSTINPLL reset. Pulled-up to PS_1V8.
J2.C35EN_PLINEnable programable logic power-up.
J2.C36EN_GT_RINEnable right GTH transceiver power-up.
J2.C37PLL_FDECINPLL Frequency decrementation.
J2.C44 / J2.C45 / J2.C46 / J2.C47MODE3..0INBoot mode selection 2):
  • JTAG
  • QUAD-SPI (32 Bit)
  • SD1 (2.0)
  • eMMC (1.8 V)
  • SD1 LS (3.0)

Supported Modes depends also on used Carrier.

J2.D29EN_PLL_PWRINEnable PLL power supply.
J2.D30PLL_FINCINPLL Frequency incrementation.
J2.D31PLL_LOLnOUTLoss of lock status.
J2.D32PLL_SEL1INPLL clock selection.
J2.D33PG_GT_ROUTRight GTH Transceivers powered-up.
J2.D37PSBATTINPS RTC Battery supply voltage 2) 3).
J2.D38PUDC_BINConfiguration pull-ups setting 2). Pulled-up to PL_1V8.
J2.D45 / J2.D46DX_P / DX_N-SoC temperatur sensing diode pins 2).

1) Direction:

    • IN: Input from the point of view of this board.
    • OUT: Output from the point of view of this board.

2) See UG1085 for additional information.

3) See Recommended Operating Conditions.

Controller signal.

Power and Power-On Sequence


Power Rails

Power Rail Name/ Schematic NameConnector + PinDirection1)Notes
VCCO_66J1.A32 / J1.A33IN
VREF_66J1.A41IN
3.3VINJ1.A54 / J1.A55 / J1.B55 / J1.B56IN

PL_1V8

J1.C32 / J1.C33 / J1.D33 / J1.D34OUT
PL_DCINJ1.C56 / J1.C57 / J1.C58 / J1.C59 / J1.C60 / J1.D56 / J1.D57 / J1.D58 / J1.D59 / J1.D60IN
LP_DCDCJ2.A50 / J2.A51 / J2.A52 / J2.B50 / J2.B51 / J2.B52 / J2.C50 / J2.C51 / J2.C52 / J2.D50 / J2.D51 / J2.D52IN
DCDCINJ2.A57 / J2.A58 / J2.A59 / J2.A60 / J2.B57 / J2.B58 / J2.B59 / J2.B60 / J2.C57 / J2.C58 / J2.C59 / J2.C60 / J2.D57 / J2.D58 / J2.D59 / J2.D60 / IN
PS_BATTJ2.D37IN
DDR_1V2J2.D47OUT
PS_1V8J2.C34 / J2.D34 / J3.A56 / J3.B56 / J3.C56 / J3.D56OUT
PLL_3V3J3.A55IN
GT_DCDCJ3.A59 / J3.A60 / J3.B59 / J3.B60 / J3.C59 / J3.C60 / J3.D59 / J3.D60 /IN
VCCO_48J3.C7 / J3.C8 / J3.D8 / J3.D9IN
VCCO_47J3.C19 / J3.C20 / J3.D20 / J3.D21IN
VCCO_64J4.B21 / J4.B39IN
VREF_64J4.B30IN
VCCO_65J4.C21 / J4.C39IN
VREF_65J4.C30IN

1) Direction:

    • IN: Input from the point of view of this board.
    • OUT: Output from the point of view of this board.
Module power rails.

Recommended Power up Sequencing


The power up sequencing highly depends on the use case. In general, it should be possible to enable/disable the processing system (PS) / programmable logic (PL) independently. Furthermore, within the processing logic it should be possible to enable/disable only low-power domain and/or low-power and full-power domain. Additionally, usage of GTR for PS side and GTH for PL side should be possible. GTH transceivers on left and right side are usable independently. Because of this flexibility the needed parts of the following table needs to be selected individually. For detailed information take a look into schematics.

SequenceNet nameRecommended Voltage RangePull-up/downDescriptionNotes
0---Configuration signal setup.See Configuration and System Control Signals.
1 1)PSBATT1.2 V ... 1.5 V-Battery connection.Battery Power Domain usage. When not used, tie to GND.
13.3VIN3.3 V (± 5 %)-Management power supply.Management module power supply. 0.5 A recommended.
GTH / GTR Transceiver clocking (Only necessary in cases where the PLL clock is used for GTH / GTR.):
1 1)GT_DCDC3.3 V (± 5 %) 2)
GTH transceiver power supply.Main module power supply for GTH / GTY transceiver. 5 A recommended. Power consumption depends mainly on design and cooling solution.
1 1)EN_PLL_PWR-PU 3), 3.3VINPLL power enable.
1 1)PG_PLL_1V8-PU 3), 3.3VINPLL power good status.
1 1)PLL_3V33.3 V (± 5 %)
PLL power supply
2Processing System (PS):

Procedure for PS starting.
2.1Low-power domain:Bring-up for low-power domain PS.
2.1.1LP_DCDC3.3 V (± 5 %) 2)-Low-power domain power supply.Main module power supply for low-power domain. 5.5 A recommended. Power consumption depends mainly on design and cooling solution.
2.1.2EN_LPD-PU 3), 3.3VINLow-power domain power enable.
2.1.3LP_GOOD-PU 3), 3.3VINLow-power domain power good status.Module power-on sequencing for low-power domain finished.
2.2Full-power domain:Bring-up for full-power domain PS.Full-power PS domain needs powered low-power PS domain.
2.2.1DCDCIN3.3 V (± 5 %) 2)
Full-power domain and GTR transceiver power supply.Main module power supply for full-power domain. 7 A recommended. Power consumption depends mainly on design and cooling solution.
2.2.2EN_FPD3.3 V-Full-power domain power enable.
2.2.3PG_FPD-PU 3), 3.3VINFull-power domain power good status.Module power-on sequencing for full-power domain finished.
2.2.4EN_DDR3.3 V-DDR memory power enable.
2.2.5PG_DDR
PU 3), 3.3VINDDR memory power good status.Module power-on sequencing for DDR memory finished.

2.3

GTR TransceiverProcedure for GTR transceiver starting.PS transceiver usage needs powered PS (low- and full-power domain).
2.3.1EN_PSGT3.3 V-GTR transceiver power enable.
2.3.2PG_PSGT-PU 3), 3.3VINGTR transceiver power good status.Module power-on sequencing for GTR transceiver finished.
2Programmable Logic (PL)Procedure for PL starting.PS and PL can be started independently.
2.1PL_DCIN3.3 V (± 5 %) 2)-Programmable logic power supply.Main module power supply for programmable logic. 12 A recommended. Power consumption depends mainly on design and cooling solution.
2.2EN_PL-PU 3), 3.3VINProgrammable logic power enable.
2.3PG_PL-PU 3), 3.3VINProgrammable logic power good status.Module power-on sequencing for programmable logic finished. Periphery and variable bank voltages can be enabled on carrier.
2.4VCCO_47 / VCCO_48 / VCCO_64 / VCCO_65 / VCCO_66 4)-Module bank voltages.Enable bank voltages after PG_PL deassertion.
3GTH / GTY TransceiverProcedure for GTH / GTY transceiver starting.PL transceiver usage needs powered PL and low-power PS domain.
3.1GT_DCDC3.3 V (± 5 %) 2)-GTH transceiver power supply.Main module power supply for GTH transceiver. 5 A recommended. Power consumption depends mainly on design and cooling solution.
3.2EN_GT_L / EN_GT_R3.3 V-GTH / GTY left / right transceiver power enable.Transceivers on left / right side can be used independently.
3.3PG_GT_L / PG_GT_R-PU 3), 3.3VINGTH / GTY transceiver power good status.

1) (optional)

2) Dependent on the assembly option a higher input voltage may be possible. 

3) (on module)

4) See DS925 for additional information.

Baseboard Design Hints

Board to Board Connectors

5.2 x 7.6 cm UltraSoM+ modules use four Samtec AcceleRate HD High-Density Slim Body Arrays on bottom side.
  • 4x ADM6-60-01.5-L-4-2 (240 pins, 60 per row)
    •  Mates with ADF6-60-03.5-L-4-2

5.2 x 7.6 cm UltraSoM+ carrier use four Samtec AcceleRate HD High-Density Slim Body Arrays on top side.

  • 4x ADF6-60-03.5-L-4-2 (160-pins)
    • Mates with ADM6-60-01.5-L-4-2
Features
  • Board-to-Board Connector 240-pins, 60 contacts per row
  • 0.025" (0.635 mm) pitch
  • Data Rate: max 56 Gbps 
  • Mates with: ADM6/APF6
  • Insulator Material: LCP, Black
  • Contact Material:  Copper Alloy
  • Plating: Au or Sn over 50 µ" (1.27 µm) N
  • Operating Temperature Range: -55 ºC to +125 ºC
  • PCIe 5.0 capable: Yes
  • Lead-Free Solderable: Yes
  • RoHS Compliant: Yes
Connector Stacking height

When using the standard type on baseboard and module, the mating height is 5 mm.

Other mating heights are possible by using connectors with a different height:

Order numberREF numberSamtec NumberTypeContribution to stacking heightComment
30095REF-30095ADM6-60-01.5-L-4-2Module connector1.5 mmStandard connector used on modules
31137REF-31137ADF6-60-03.5-L-4-2Baseboard connector3.5 mmStandard connector used on carrier
Connectors.
Connector Speed Ratings

The  AcceleRate HD High-Density  connector speed rating depends on the stacking height; please see the following table:

Stacking heightSpeed rating
5 mm56 Gbps
Speed rating.
Current Rating

Current rating of  Samtec AcceleRate HD High-Density B2B connectors is 1.34 A per pin (4 pins powered)

Connector Mechanical Ratings
  • Shock: 100G, 6 ms Sine
  • Vibration: 7.5G random, 2 hours per axis, 3 axes total


Manufacturer Documentation


Technical Specifications

Absolute Maximum Ratings *)

Power Rail Name/ Schematic NameDescriptionMinMaxUnit
LP_DCDCMicromodule Power-0.3006.0V
DCDCINMicromodule Power-0.3007.0V
GT_DCDCMicromodule Power-0.3006.0V
PL_DCINMicromodule Power-0.300

7.0

V
3.3VINMicromodule Power-0.3003.600V
PLL_3V3PLL power supply-0.5003.8V
PS_BATTRTC / BBRAM-0.5002.000V
VCCO_47HD IO Bank power supply-0.5003.400V
VCCO_48HD IO Bank power supply-0.5003.400V
VCCO_64HP IO Bank power supply-0.5002.000V

VCCO_65

HP IO Bank power supply-0.5002.000V
VCCO_66HP IO Bank power supply-0.5002.000V
VREF_64Bank input reference voltage-0.5002.000V
VREF_65Bank input reference voltage-0.5002.000V
VREF_66Bank input reference voltage-0.5002.000V
Module absolute maximum ratings

*) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Condition. Exposure to absolute-maximum rated conditions for extended periods may affect device reliability.

Recommended Operating Conditions

This TRM is generic for all variants. Temperature range can be differ depending on the assembly version. Voltage range is mostly the same during variants (exceptions are possible, depending on custom request).

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

  • Variants of modules are described here: Article Number Information
  • Modules with commercial temperature grade are equipped with components that cover at least the range of 0°C to 75°C
  • Modules with extended temperature grade are equipped with components that cover at least the range of 0°C to 85°C
  • Modules with industrial temperature grade are equipped with components that cover at least the range of -40°C to 85°C
  • The actual operating temperature range will depend on the FPGA / SoC design / usage and cooling and other variables.


ParameterMinMaxUnitsReference Document
LP_DCDC 1)3.2013.399V
DCDCIN 1)3.1353.465V
GT_DCDC 1)3.2013.399V
PL_DCIN 1)3.135

3.465

V
3.3VIN3.1353.465V
PLL_3V33.2013.399V
PS_BATT1.2001.500VSee FPGA datasheet.
VCCO_471.1643.399VSee FPGA datasheet.
VCCO_481.1643.399VSee FPGA datasheet.
VCCO_640.9701.854VSee FPGA datasheet.

VCCO_65

0.9701.854VSee FPGA datasheet.
VCCO_660.9701.854VSee FPGA datasheet.
VREF_640.61.2VSee FPGA datasheet.
VREF_650.61.2VSee FPGA datasheet.
VREF_660.61.2VSee FPGA datasheet.

1) Higher values may possible. For more information consult schematic and according datasheets.

Recommended operating conditions.


Physical Dimensions

  • Module size: 76 mm × 52 mm.  Please download the assembly diagram for exact numbers.

  • Mating height with standard connectors: 5 mm.

PCB thickness: 1.6 mm (± 10 %).

Physical Dimension

Currently Offered Variants 

Trenz shop TE0818 overview page
English pageGerman page
Trenz Electronic Shop Overview

Revision History

Hardware Revision History

Board hardware revision number.


DateRevisionChangesDocumentation Link
-REV02
  1. Added capacitors C178, C187, C188, C189 (470nF) to VTT net.
  2. Added U18/ U37 compensation network: R119, C190, C191. R118 is optional jumper and is installed when using the internal compensation network. External compensation network is used by default.
  3. Connected all DDR4 TEN pins together and pulled them down with resistor R120 and added testpoint TP23.
  4. Added testpoints TP25, TP27, TP29, TP35, TP37...TP79.
  5. Changed capacitor C112 size from 0402 to 0201 and voltage rating from 16 V to 10 V.
  6. Changed ferrid beads from MPZ0603S121HT000 to BLM15PX800SZ1D for L1, L2, L3, L4, L5, and L7.
  7. Changed ferrid beads from MPZ1608S221A to BLM15PX800SZ1D for L6 and L8.
  8. Added diode D2 between U41 pin 3 net MR and voltage rail 3.3VIN.
  9. Modified trace length.
  10. Updated documentation overviews.
REV02
-REV01First Production ReleaseREV01
Hardware Revision History

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Document Change History

DateRevisionContributorDescription

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • Added power supply PLL_3V3 in table "Recommended Power up Sequencing".
  • Fix typo.

2023-09-20

v.16

ED

  • Updated for REV02

2023-01-12

v.13

ED

  • Initial Document

--

all

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • --
Document change history.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]


Table of contents


  • No labels