...
Page properties |
---|
|
Template Revision 2.0 - on construction2 TRM Name always "TE Series Name" +TRM, for example "TE0720 TRM" |
...
Page properties |
---|
|
Important General Note: |
Page properties |
---|
|
----------------------------------------------------------------------- |
Page properties |
---|
|
Note for Download Link of the Scroll ignore macro: |
Scroll pdf ignore |
---|
Table of Contents |
Overview
The Trenz Electronic TE0714 is an industrial-grade SoM (System on Module) based on Xilinx Artix-7, 16 MByte Flash memory and powerful switching mode power supplies for all on-board voltages. A large number of configurable I/O's is provided via rugged high-speed stacking strips. TE0714 is the smallest module with transceiver (3 x 4 cm).
Refer to http://trenz.org/te0714-info for the current online version of this manual and other available documentation.
Key Features
Page properties |
---|
|
----------------------------------------------------------------------- |
Page properties |
---|
|
Notes : - List of key features of the PCB
|
Xilinx Artix-7 FPGA (A15T, A35T, A50T)
- Rugged for shock and high vibration
- 16 MByte QSPI Flash memory
- Differential MEMS oscillator for MGT clocking
- MEMS oscillator for PL clocks (Optional)
- Plug-on module with 2 × 100-pin high-speed hermaphroditic strips
- 144 FPGA I/O's (Max 68 differential)
- XADC analog input
- 4 GTP (high-performance transceiver) lanes
- GT reference clock inputs
- Optimized I/O and power pins for good signal integrity
- On-board high-efficiency DC-DC converters
- Power supply for all on-board components
- eFUSE bit-stream encryption (AES)
- One user configurable LED
Different configurations for cost and performance optimization available upon request. Available options are:
- FPGA Type (A15T, A35T, A50T), temperature grade
- GT clock frequency (or none if not implemented)
- PL clock frequency and precision (or none if not implemented)
- Config and B14 bank Voltage: 1.8V or 3.3V
- SPI Flash type (or none if not implemented)
- LED Color (or none if not implemented)
- PUDC Pin strapping (pull high or pull down)
- GT power enable pin strapping (default power enabled or disabled)
Block Diagram
...
anchor | Figure_1 |
---|
title | Figure 1: TE0714 block diagram |
---|
Note for Download Link of the Scroll ignore macro: |
Scroll pdf ignore |
---|
Table of Contents |
Overview
The Trenz Electronic TE0714 is an industrial-grade SoM (System on Module) based on Xilinx Artix-7, 16 MByte Flash memory and powerful switching mode power supplies for all on-board voltages. A large number of configurable I/O's is provided via rugged high-speed stacking strips. TE0714 is the smallest module with transceiver (3 x 4 cm).
Refer to http://trenz.org/te0714-info for the current online version of this manual and other available documentation.
Key Features
Page properties |
---|
|
Notes : - List of key features of the PCB
|
Xilinx Artix-7 FPGA (A15T, A35T, A50T)
- Rugged for shock and high vibration
- 16 MByte QSPI Flash memory
- Differential MEMS oscillator for MGT clocking
- MEMS oscillator for PL clocks (Optional)
- Plug-on module with 2 × 100-pin high-speed hermaphroditic strips
- On-board high-efficiency DC-DC converters
- Power supply for all on-board components
- eFUSE bit-stream encryption (AES)
- One user configurable LED
Different configurations for cost and performance optimization available upon request. Available options are:
- FPGA Type (A15T, A35T, A50T), temperature grade
- GT clock frequency (or none if not implemented)
- PL clock frequency and precision (or none if not implemented)
- Config and B14 bank Voltage: 1.8V or 3.3V
- SPI Flash type (or none if not implemented)
- LED Color (or none if not implemented)
- PUDC Pin strapping (pull high or pull down)
- GT power enable pin strapping (default power enabled or disabled)
Block Diagram
Scroll Title |
---|
anchor | Figure_OV_BD |
---|
title | TE0714 block diagram |
---|
|
|
...
Scroll Only |
---|
Image Removed |
Main Components
Page properties |
---|
|
Notes : - Picture of the PCB (top and bottom side) with labels of important components
- Add List below
|
Scroll Title |
---|
anchor | Figure_2 |
---|
title | Figure 2: TE0714 main components |
---|
|
Scroll Ignore |
---|
draw.io Diagram |
---|
| border | true | viewerToolbar | true |
---|
| |
---|
fitWindow | false |
---|
diagramName |
---|
| MCfalse | widthtrue | links | auto |
---|
tbstyle | top |
---|
lbox | true |
---|
diagramWidth | 641 |
---|
revision |
---|
| 2
---|
Scroll Only |
---|
Image Removed |
|
- Xilinx Artix-7 FPGA (XC7A series), U4
- 16 MByte SPI Flash, U7
- B2B connector Samtec Razor Beam™ LSHM-150, JM2
- B2B connector Samtec Razor Beam™ LSHM-150, JM1
- 25 MHz oscillator, U8
- Single output low-dropout linear regulator (1.2V_MGT), U6
- Single output low-dropout linear regulator (1.0V_MGT), U5
- Low-jitter precision LVDS 125 MHz oscillator (GT Clock), U2
- Red indication LED, D4
- Step-down DC-DC converter (1.0V), U1
- PFET load switch with configurable slew rate (3.3V), Q1
- Low-power step-down DC-DC converter (1.8V), U3
- Voltage detector for circuit initialization and timing supervision, U23
Image Added |
|
Main Components
Page properties |
---|
|
Notes : - Picture of the PCB (top and bottom side) with labels of important components
- Add List below
|
Scroll Title |
---|
anchor | Figure_OV_MC |
---|
title | TE0714 main components |
---|
|
Scroll Ignore |
---|
draw.io Diagram |
---|
border | false |
---|
viewerToolbar | true |
---|
| |
---|
fitWindow | false |
---|
diagramName | MC-TE0714 |
---|
simpleViewer | true |
---|
links | auto |
---|
tbstyle | top |
---|
lbox | true |
---|
diagramWidth | 641 |
---|
revision | 2 |
---|
|
|
Scroll Only |
---|
Image Added |
|
- Xilinx Artix-7 FPGA (XC7A series), U4
- 16 MByte SPI Flash, U7
- B2B connector Samtec Razor Beam™ LSHM-150, JM2
- B2B connector Samtec Razor Beam™ LSHM-150, JM1
- 25 MHz oscillator, U8
- Single output low-dropout linear regulator (1.2V_MGT), U6
- Single output low-dropout linear regulator (1.0V_MGT), U5
- Low-jitter precision LVDS 125 MHz oscillator (GT Clock), U2
- Red indication LED, D4
- Step-down DC-DC converter (1.0V), U1
- PFET load switch with configurable slew rate (3.3V), Q1
- Low-power step-down DC-DC converter (1.8V), U3
- Voltage detector for circuit initialization and timing supervision, U23
Initial Delivery State
Initial Delivery State
Scroll Title |
---|
anchor | Table_1 |
---|
title | Table 1: Initial delivery state of programmable devices on the module. |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
style | widths | sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
Storage device name | Content | Notes |
---|
SPI Flash OTP Area | Empty, not programmed | Except serial number programmed by flash vendor |
SPI Flash Quad Enable bit | Programmed | SPI Flash main array | demo design | eFUSE USER | Not programmed | eFUSE Security | Not programmed | Control Signals
Page properties |
---|
|
- Overview of Boot Mode, Reset, Enables,
|
Boot process is controlled by signals on the board to board (B2B) connector.
Scroll Title |
---|
anchor | Table_2OV_IDS |
---|
title | Table 2: Boot signals.Initial delivery state of programmable devices on the module. |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default | style |
---|
widths | 30%,25%,45% | widths |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
SignalDirection | Signal State | Description | BOOTMODEinput | high or open | Master SPI, x4 Mode
| low or ground
| Slave SelectMAP | PROG_B | input | pulsed low | Clear FPGA configuration (falling edge) and initiate a new configuration sequenz (next rising edge). | DONE | output | high | Completion of configuration sequence. | |
Note |
---|
SPI FPGA pins D02 and D03 have no pull-ups on the module, so with PUDC=High option, those pins are floating if there are no pull-ups on baseboard. As those pins have SPI RESET function when Quad mode is not enabled, it is mandatory to either add pull-ups on user baseboard or program the Quad Enable bit in Flash nonvolatile status register. |
Signals, Interfaces and Pins
Page properties |
---|
|
Notes : - For modules which needs carrier us only classes and refer to B2B connector if more than one is used, for example
|
JTAG Interface
JTAG access to the Xilinx Artix-7 FPGA device is provided through connector JM1.
...
anchor | Table_3 |
---|
title | Table 3: JTAG signals. |
---|
Notes |
---|
SPI Flash OTP Area | Empty, not programmed | Except serial number programmed by flash vendor | SPI Flash Quad Enable bit | Programmed |
| SPI Flash main array | demo design |
| eFUSE USER | Not programmed |
| eFUSE Security | Not programmed |
|
|
...
Control Signals
Page properties |
---|
|
- Overview of Boot Mode, Reset, Enables,
|
Boot process is controlled by signals on the board to board (B2B) connector.
Scroll Title |
---|
anchor | Table_OV_BS |
---|
title | Boot signals. |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
widths | 16%,14%,19%,51 |
---|
|
|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
|
...
...
...
JM1:91
On-board LED's
There is one LED on TE0714 module:
...
anchor | Table_4 |
---|
title | Table 4: LED connection. |
---|
...
LED
...
Color
...
FPGA
...
Notes
...
D4
...
Red
...
K18
Clock
...
anchor | Table_5 |
---|
title | Table 5: Clock signals. |
---|
...
Clock
...
Default Frequency
...
IC
...
FPGA
...
Notes
...
25 MHz
...
U8
...
T14
...
125MHz
...
U2
...
B6/B5
...
Frequency depends on the module variant
Signal State | Description |
---|
BOOTMODE
| input | high or open | Master SPI, x4 Mode
| low or ground
| Slave SelectMAP | PROG_B | input | pulsed low | Clear FPGA configuration (falling edge) and initiate a new configuration sequenz (next rising edge). | DONE | output | high | Completion of configuration sequence. |
|
Note |
---|
SPI FPGA pins D02 and D03 have no pull-ups on the module, so with PUDC=High option, those pins are floating if there are no pull-ups on baseboard. As those pins have SPI RESET function when Quad mode is not enabled, it is mandatory to either add pull-ups on user baseboard or program the Quad Enable bit in Flash nonvolatile status register. |
Signals, Interfaces and Pins
Page properties |
---|
|
Notes : - For modules which needs carrier us only classes and refer to B2B connector if more than one is used, for example
|
JTAG Interface
JTAG access to the Xilinx Artix-7 FPGA device is provided through connector JM1.
Board to Board (B2B) I/Os
FPGA bank number and number of I/O signals connected to the B2B connector:
Scroll Title |
---|
anchor | Table_SIP_6JTAG |
---|
title | Table 6: B2B I/OsJTAG signals. |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default | style | widths |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
FPGA Bank ConnectorI/O Signal Count | Voltage Level | Notes | 14 | JM1 | 6 | VCCIO_0 | 14 | JM2 | 36 | VCCIO_0 | NB! 17 LVDS pairs possible. | 15 | JM2 | 48 | VCCIO15 | Supplied by the baseboard. | 34 | JM1 | 48 | VCCIO34 | Supplied by the baseboard. | 216 | JM1 | 16 | MGT_AVCC MGT_AVTT | 4 x GTP lanes. | |
Please refer to the Pin-out tables page for additional information.
On-board Peripherals
Page properties |
---|
|
Notes : - add subsection for every component which is important for design, for example:
- Ethernet PHY
- USB PHY
- Programmable Clock Generator
- Oscillators
- eMMCs
- RTC
- FTDI
- ...
- DIP-Switches
- Buttons
- LEDs
|
16 MByte Quad SPI Flash
On-board SPI flash memory S25FL127S (U7) is used to store initial FPGA configuration. Besides FPGA configuration, remaining free flash memory can be used for user application storage. All four SPI data lines are connected to the FPGA allowing x1, x2 or x4 data bus widths. Maximum data rate depends on the bus width and clock frequency used.
Note |
---|
SPI Flash QE (Quad Enable) bit must be set to high or FPGA is unable to load its configuration from flash. By default this bit is set to high at the manufacturing plant. |
Power and Power-On Sequence
To power-up a module, power supply with minimum current capability of 1A is recommended.
TE0714 needs one single power supply with nominal of 3.3V.
Power Consumption
...
anchor | Table_7 |
---|
title | Table 7: Power Consumption |
---|
...
Pin |
---|
TCK | JM1:89 | TDI | JM1:85 | TDO | JM1:87 | TMS | JM1:91 |
|
Board to Board (B2B) I/Os
FPGA bank number and number of I/O signals connected to the B2B connector:
Scroll Title |
---|
anchor | Table_SIP_B2B |
---|
title | B2B I/Os |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
FPGA Bank | B2B Connector | I/O Signal Count | Voltage Level | Notes |
---|
14 | JM1 | 6 | VCCIO_0 |
| 14 | JM2 | 36 | VCCIO_0 | NB! 17 LVDS pairs possible. | 15 | JM2 | 48 | VCCIO15 | Supplied by the baseboard. | 34 | JM1 | 48 | VCCIO34 | Supplied by the baseboard. | 216 | JM1 | 16 | MGT_AVCC MGT_AVTT | 4 x GTP lanes. |
|
Please refer to the Pin-out tables page for additional information.
On-board Peripherals
Page properties |
---|
|
Notes : - add subsection for every component which is important for design, for example:
- Ethernet PHY
- USB PHY
- Programmable Clock Generator
- Oscillators
- eMMCs
- RTC
- FTDI
- ...
- DIP-Switches
- Buttons
- LEDs
|
Quad SPI Flash
On-board SPI flash memory S25FL127S (U7) is used to store initial FPGA configuration. Besides FPGA configuration, remaining free flash memory can be used for user application storage. All four SPI data lines are connected to the FPGA allowing x1, x2 or x4 data bus widths. Maximum data rate depends on the bus width and clock frequency used.
Note |
---|
SPI Flash QE (Quad Enable) bit must be set to high or FPGA is unable to load its configuration from flash. By default this bit is set to high at the manufacturing plant. |
On-board LED
There is one LED on TE0714 module.
Scroll Title |
---|
anchor | Table_OBP_LEDs |
---|
title | LED connection. |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
LED | Color | FPGA | Notes |
---|
D4 | Red | K18 | User programmable |
|
Clock
Scroll Title |
---|
anchor | Table_OBP_Clocks |
---|
title | Clock signals. |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
widths | 14%,15%,6%,9%,56% |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Clock | Default Frequency | IC | FPGA | Notes |
---|
CLK25MHz | 25 MHz | U8 | T14 | Frequency depends on the module variant. Output is compatible to 3.3V and 1.8V I/O standard of the FPGA bank. | MGT_CLK | 125MHz | U2 | B6/B5 | Frequency depends on the module variant |
|
Power and Power-On Sequence
To power-up a module, power supply with minimum current capability of 1A is recommended.
TE0714 needs one single power supply with nominal of 3.3V.
Power Consumption
Scroll Title |
---|
anchor | Table_PWR_PC |
---|
title | Power Consumption |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Test Condition (25 °C ambient) | VIN Current mA | Notes |
---|
TE0714-35, TEBT0714, empty design, GT not enabled | 110mA |
|
|
Actual power consumption depends on the FPGA design and ambient temperature.
Power Distribution Dependencies
Scroll Title |
---|
anchor | Figure_PWR_PD |
---|
title | Power Distribution |
---|
|
Scroll Ignore |
---|
draw.io Diagram |
---|
border | false |
---|
viewerToolbar | true |
---|
| |
---|
fitWindow | false |
---|
diagramName | PD-TE0714 |
---|
simpleViewer | true |
---|
links | auto |
---|
tbstyle | top |
---|
lbox | true |
---|
diagramWidth | 641 |
---|
revision | 10 |
---|
|
|
Scroll Only |
---|
Image Added |
|
Power-On Sequence
There is no specific or special power-on sequence, single power source is needed as VIN, rest of the sequence is automatic.
Scroll Title |
---|
anchor | Figure_PWR_PS |
---|
title | Power-On Sequency |
---|
|
...
Actual power consumption depends on the FPGA design and ambient temperature.
Power Distribution Dependencies
Scroll Title |
---|
anchor | Figure_3 |
---|
title | Figure 3: Power Distribution |
---|
|
Scroll Ignore |
---|
draw.io Diagram |
---|
border | truefalse |
---|
viewerToolbar | true |
---|
| |
---|
fitWindow | false |
---|
diagramName | PD-TE0714 |
---|
simpleViewer | false |
---|
TE0714-02_Power_Sequenz | simpleViewer | true |
---|
links | auto |
---|
tbstyle | top |
---|
lbox | true | width |
---|
diagramWidth | 641 |
---|
revision | 32 |
---|
|
|
Scroll Only |
---|
Image Removed |
|
Power-On Sequence
There is no specific or special power-on sequence, single power source is needed as VIN, rest of the sequence is automatic.
Image Added |
|
Power Power Rails
Scroll Title |
---|
anchor | Table_PWR_8PR |
---|
title | Table 8: Power Rails |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default | style |
---|
widths | sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
| | | Direction | Note |
---|
VIN | 98, 100 | - | input | supply voltage | VCCIO_0 | - | 54 | input | high range bank voltage | VCCIO_15 | - | 53 | input | high range bank voltage | VCCIO_34 | 62 | - | input | high range bank voltage | 3.3V | 84 | - | output | internal 3.3V voltage level | 1.8V | - | 17 | output | internal 1.8V voltage level |
|
Bank Voltages
Scroll Title |
---|
anchor | Table_PWR_9BV |
---|
title | Table 9: Bank Voltages |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default | stylewidths | default |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
| | |
---|
0 Config and B14 | 1.8V or 3.3V | Depends on module assembly variant. See R21, R22 and R27 assembly option* | 15 | User | Supplied from baseboard via B2B connector, max 3.3V | 34 | User | Supplied from baseboard via B2B connector, max 3.3VB2B connector, max 3.3V |
- *R21 assembled: 3.3V and B2B is output if R27 is assembled
- *R22 assembled 1.8V and B2B is output if R27 is assembled
- *R21 and R22 not assembled , B2B is input and carrier defines voltage → pay attention on assembled flash!
|
Board to Board Connectors
Page properties |
---|
|
- This section is optional and only for modules.
- use "include page" macro and link to the general B2B connector page of the module series, for example: 4 x 5 SoM LSHM B2B Connectors
|
Include Page |
---|
| 3 x 4 x 5 SoM LSHM B2B Connectors |
---|
| 3 x 4 x 5 SoM LSHM B2B Connectors |
---|
|
Technical Specifications
Absolute Maximum Ratings
Scroll Title |
---|
anchor | Table_10TS_AMR |
---|
title | Table 10: Module absolute maximum ratings. |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default | style | widths |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Parameter | Min | Max | Units | Reference Document |
---|
VIN supply voltage | -0.1 | 6.0 | V | - | HR I/O banks supply voltage (VCCO) | -0.5 | 3.6 | V | Xilinx datasheet DS181 | HR I/O banks input voltage | -0.4 | VCCO + 0.55 | V | Xilinx datasheet DS181 | GTP transceivers Tx/Rx input voltage | -0.5 | 1.26 | V | Xilinx datasheet DS181 | Voltage on module JTAG pins | -0.4 | VCCO_0 + 0.55 | V | Xilinx datasheet DS181 | Storage temperature | -40 | +85 | °C | - |
|
Recommended Operating Conditions
.55 | V | Xilinx datasheet DS181 | Storage temperature | -40 | +100 | °C | - |
|
Recommended Operating Conditions
Scroll Title |
---|
anchor | Table_TS_ROC |
---|
title | Recommended Operating Conditions |
---|
|
This TRM is generic for all variants. Variants of modules are described here: Article Number Information Modules with commercial temperature grade are equipped with components that cover at least the range of 0°C to 75°C Modules with extended temperature grade are equipped with components that cover at least the range of 0°C to 85°C Modules with industrial temperature grade are equipped with components that cover at least the range of -40°C to 85°C The actual operating temperature range will depend on the FPGA / SoC design / usage and cooling and other variables. |
Scroll Title |
---|
|
anchor | Table_11 |
---|
title | Table 11: Recommended Operating Conditions Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default | style | widths |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
| Parameter | Min | Max | Units | Reference Document |
---|
VIN supply voltage | 3.135 | 3.45 | V | - |
HR I/O banks supply voltage (VCCO) | 1.14 | 3.465 | V | Xilinx datasheet DS181 |
HR I/O banks input voltage | -0.20 | VCCO + 0.20 | V | Xilinx datasheet DS181 |
Voltage on module JTAG pins | 3.135 | 3.465 | V | Xilinx datasheet DS181 |
Physical Dimensions
Module size: 40 mm × 30 mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: 8 mm
PCB thickness: 1.6 mm
Highest part on PCB: approximately 2.5 mm. Please download the step model for exact numbers.
All dimensions are shown in mm. Additional sketches, drawings and schematics can be found here.
Scroll Title |
---|
anchor | Figure_4 |
---|
title | Figure 4: Physical dimensions drawing |
---|
|
Image Removed Image Removed |
Weight
| sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
Parameter | Min | Max | Units | Reference Document |
---|
VIN supply voltage | 3.135 | 3.45 | V | - | HR I/O banks supply voltage (VCCO) | 1.14 | 3.465 | V | Xilinx datasheet DS181 | HR I/O banks input voltage | -0.20 | VCCO + 0.20V | V | Xilinx datasheet DS181 | Voltage on module JTAG pins | 0 | VCCO_0 + 5% | V | Xilinx datasheet DS181 |
|
Physical Dimensions
Module size: 40 mm × 30 mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: 8 mm
PCB thickness: 1.6 mm
Highest part on PCB: approximately 2.5 mm. Please download the step model for exact numbers.
All dimensions are shown in mm. Additional sketches, drawings and schematics can be found here.
Scroll Title |
---|
anchor | Figure_TS_PD |
---|
title | Physical dimensions drawing |
---|
|
Image Added Image Added |
Variants Currently In Production
Scroll Title |
---|
anchor | Table_VCP_12SO |
---|
title | Table 12: Module WightTrenz Electronic Shop Overview |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default | style | widths |
---|
sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
|
Variant | Weight in g | Note |
---|
2IC6 | 8.3 | Plain Module |
Variants Currently In Production
...
Set correct link to the shop page overview table of the product on English and German, if not available, set
Note |
---|
On REV 01 JM2 Pin 54 was connected to GND. When R27 is not populated, REV 02 is backwards compatible to REV 01. When R27 is set, check your baseboard to not connect this pin to GND. For all new baseboards JM2.54 should be used as VCCIO output (it will then be 1.8V or 3.3V depending the voltage settings on the module. |
Revision History
Hardware Revision History
...
https://shop.trenz-electronic.de/de/Produkte/Trenz-Electronic/
...
Scroll Title |
---|
anchor | Table_13RH_HRH |
---|
title | Table 13: Trenz Electronic Shop Overview Hardware Revision History |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default | style |
---|
widths | sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
|
Trenz shop TE0714 overview page |
---|
English page | German page |
Note |
---|
On REV 01 JM2 Pin 54 was connected to GND. When R27 is not populated, REV 02 is backwards compatible to REV 01. When R27 is set, check your baseboard to not connect this pin to GND. For all new baseboards JM2.54 should be used as VCCIO output (it will then be 1.8V or 3.3V depending the voltage settings on the module. |
Revision History
Hardware revision number is printed on the PCB board next to the module model number separated by the dash.
Image Added
Document Change
...
History
Scroll Title |
---|
anchor | Table_14RH_DCH |
---|
title | Table 14: Module absolute maximum ratings.Document change history |
---|
|
Scroll Table Layout |
---|
orientation | portrait |
---|
sortDirection | ASC |
---|
repeatTableHeaders | default | style |
---|
widths | sortByColumn | 1 |
---|
sortEnabled | false |
---|
cellHighlighting | true |
---|
|
|
Date | Revision | Note | PCN | Documentation Link |
---|
2018-11-01 | 02 | Replace obsolete SPI Flash | in preparation | TE0714-02 |
2016-08-04 | 02 | VCCIO0 added to B2B | PCN-20160815 | TE0714-02 |
01 | - | - | TE0714-01 |
Hardware revision number is printed on the PCB board next to the module model number separated by the dash.
Image Removed
Document Change History
...
Date
...
Revision
...
Authors
...
Description
...
Page info |
---|
infoType | Current version |
---|
prefix | v. |
---|
type | Flat |
---|
showVersions | false |
---|
|
...
Page info |
---|
infoType | Modified by |
---|
type | Flat |
---|
showVersions | false |
---|
|
| false |
---|
cellHighlighting | true |
---|
|
Date | Revision | Authors | Description |
---|
Page info |
---|
| modified-date |
---|
| modified-date |
---|
dateFormat | yyyy-MM-dd |
---|
|
| Page info |
---|
infoType | Current version |
---|
prefix | v. |
---|
type | Flat |
---|
showVersions | false |
---|
|
| Page info |
---|
infoType | Modified by |
---|
type | Flat |
---|
showVersions | false |
---|
|
| - Updated storage temperatur.
| 2021-04-07 | v59 | Thomas Steffens | - changed operating conditions
| 2019-03-04 | v55 | John Hartfiel | - Restore and modify v.50
- Correction max IO count on key features
- Change history table
- typo correction
| 2019-01-07 | v.50 | John Hartfiel | - Updated to TRM version 2.2
- Style modifications
| | v.48 | Martin Rohrmüller | - Updated to TRM version 2.1
- Updated B2B Connectors
- Style modifications
| 2018-09-17 | v.38 | Martin Rohrmüller | - Added power rail section
- Added Rev 02 Flash PCN
|
|
...
| 2018-09-17 | v.36 | Martin Rohrmüller | | 2018-04-04 | | Martin Rohrmüller | Corrected clock net designator in table. | 2017-05-28 |
|
...
| Jan Kumann | - Board-to-Board I/O section added.
- New physical dimensions images.
- Documents sections rearranged.
| 2017-03-20 |
|
...
| John Hartfiel | - Notes on Clocking section.
| 2017-01-27 | v.25 | Jan Kumann | | 2016-12-01 | | Jan Kumann | - Changes in the document structure, few corrections.
| 2016-11-18 | v.14
| Thorsten Trenz, Emmanuel Vassilakis | - Hardware revision 02 specific changes.
|
|
...
2016-06-01
...
...
...
Disclaimer
2016-06-01 | | | | -- | all | Page info |
---|
infoType | Modified users |
---|
type | Flat |
---|
showVersions | false |
---|
|
| -- |
|
...
Disclaimer
Include Page |
---|
| IN:Legal Notices |
---|
| IN:Legal Notices |
---|
|
Refer to https://wiki.trenz-electronic.de/display/PD/TE0713+TRM for online version of this manual and the rest of available documentation.