Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
HTML
<!--
Template Revision 1.68
(HTML comments will be not displayed in the document, no need to remove them. For Template/Skeleton changes, increase Template Revision number. So we can check faster, if the TRM style is up to date).
-->
HTML
<!--
General Notes:
If some section is CPLD firmware dependent, make a note and if available link to the CPLD firmware description. It's in the TE shop download area in the corresponding module -> revision -> firmware folder.
-->
HTML
<!--
General Notes:
Designate all graphics and pictures with a number and a description. For example "Figure 1: TE07xx-xx Block Diagram" or "Table 1: Initial delivery state". "Figure x" and "Table x" have to be formatted to bold.  
-->
HTML
<!--
Link to the base folder of the module (remove de/ or en/ from the URL): for example:
https://shop.trenz-electronic.de/Download/?path=Trenz_Electronic/Modules_and_Module_Carriers/4x5/4x5_Carriers/TE0703/
  -->
Scroll Ignore

Download PDF version of this document.

Scroll pdf ignore

Table of Contents

Table of Contents

Overview

The Trenz Electronic TE0807 is an industrial-grade MPSoC SoM integrating a Xilinx Zynq UltraScale+ MPSoC, up to 8 GBytes of DDR4 SDRAM via 64bit wide data bus, max. 512 MByte Flash memory for configuration and operation, 20 Gigabit transceivers and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/Os are provided via rugged high-speed stacking connections. All this in a compact 5.2 x 7.6 cm form factor, at the competitive price.

HTML
<!--
Use short link the Wiki Ressource page: for example:
http://trenz.org/te0720-info
List of available short links: https://wiki.trenz-electronic.de/display/CON/Redirects
  -->
Scroll Only (inline)
Refer to http://trenz.org/te0807-info for the current online version of this manual and other available documentation.

Key Features

  • MPSoC: ZYNQ UltraScale+ ZU7EV 900-pin package
  • Memory
    - 64bit DDR4, 8 GByte maximum
    - Dual SPI boot Flash in parallel, 512 MByte maximum
  • User I/Os
    - 65 x PS MIOs, 48 x PL HD GPIOs,  156 x PL HP GPIOs (3 banks)
    - Serial transceivers: 4 x GTR + 16 x GTH
    - Transceiver clocks inputs and outputs
    - PLL clock generator inputs and outputs
  • Si5345 - 10 output PLL
  • All power supplies on board, single 3.3V power source required
    - 14 on-board DC-DC regulators and 13 LDOs
    - LP, FP, PL separately controlled power domains
  • Support for all boot modes (except NAND) and scenarios
  • Support for any combination of PS connected peripherals
  • Size: 52 x 76 mm, 3 mm mounting holes for skyline heat spreader
  • B2B connectors: 4 x 160 pin


Additional assembly options are available for cost or performance optimization upon request.

Block Diagram

HTML
<!--
Rules for all diagrams:
1. All diagrams are wrapped in the "Scroll Title" macro.
	- The title has to be named with the diagrams name
	- The anchor has the designation figure_x, whereby x is the number of the diagram

2. The Draw.IO diagram has to be inserted in the "Scroll Ignore" macro
	- Border has to be switched off in the macro edit
	- Toolbar has to be hidden in the macro edit

3. A PNG Export of the diagram has to be inserted in the "Scroll Only" macro 

The workaround with the additional PNG of the diagram is necessary until the bug of the Scroll PDF Exporter, which cuts diagram to two pages, is fixed.


IMPORTANT NOTE: In case of copy and paste the TRM skeleton to a new Wiki page, delete the Draw.IO diagrams and the PNGs, otherwise due to the linkage of the copied diagrams every change in the TRM Skeleton will effect also in the created TRM and vice versa!

See page "Diagram Drawing Guidelines" how to clone an existing diagram as suitable template for the new diagram! 

   -->
Scroll Title
anchorFigure_1
titleFigure 1: TE0807-01 block diagram
Scroll Ignore


Scroll Only


Main Components

Scroll Title
anchorFigure_2
titleFigure 2: TE0807-01 main components
Scroll Ignore


Scroll Only



  1. Xilinx ZYNQ UltraScale+ XCZU9EG MPSoC, U1
  2. Low-power programmable oscillator @ 33.333333 MHz (PS_CLK), U32
  3. Red LED (DONE), D1
  4. 256Mx16 DDR4-2400 SDRAM, U12
  5. 256Mx16 DDR4-2400 SDRAM, U9
  6. 256Mx16 DDR4-2400 SDRAM, U2
  7. 256Mx16 DDR4-2400 SDRAM, U3
  8. 12A PowerSoC DC-DC converter, U4
  9. Quartz crystal, Y1
  10. Low-power programmable oscillator @ 25.000000 MHz (IN0 for U5), U25
  11. 10-channel programmable PLL clock generator, U5
  12. Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J4
  13. Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J2
  14. Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J3
  15. Ultra fine 0.50 mm pitch, Razor Beam™ LP Slim Terminal Strip with 160 contacts, J1
  16. Quartz crystal, Y2
  17. 256 Mbit serial NOR Flash memory, U7
  18. 256 Mbit serial NOR Flash memory, U17


Initial Delivery State

 Storage Device Name

Content

Notes

SPI Flash OTP Area

Empty, not programmed

Except serial number programmed by flash vendor.

SPI Flash Quad Enable bit

Programmed

-

SPI Flash main array

Not programmed

-

eFUSE USER

Not programmed

-

eFUSE Security

Not programmed

-
Si5345A OTP NVMNot programmed-

Table 1: Initial delivery state of programmable devices on the module

Boot Process

The boot device and mode of the Zynq UltraScale+ MPSoC can be selected via 4 dedicated pins accessible on B2B connector J2:

Boot Mode PinB2B Pin
PS_MODE0J2-109
PS_MODE1J2-107
PS_MODE2J2-105
PS_MODE3J2-103

Table 2: Boot mode pins on B2B connector J2.


Following boot modes are possible on the TE0808 UltraScale+ module by generating the corresponding 4-bit code by the pins PS_MODE0 ... PS_MODE3 (little-endian alignment):

Boot ModeMode Pins [3:0]MIO LocationDescription
JTAG0x0JTAGDedicated PS interface.
QSPI320x2MIO[12:0]

Configured on module with dual QSPI Flash Memory.

32-bit addressing.
Supports single and dual parallel
configurations.
Stack and dual stack is not
supported.

SD00x3MIO[25:13]Supports SD 2.0.
SD10x5MIO[51:38]Supports SD 2.0.
eMMC_180x6MIO[22:13]Supports eMMC 4.5 at 1.8V.
USB 00x7MIO[52:63]Supports USB 2.0 and USB 3.0.
PJTAG_00x8MIO[29:26]PS JTAG connection 0 option.
SD1-LS0xEMIO[51:39]

Supports SD 3.0 with a required SD 3.0 compliant level shifter.

Table 3: Selectable boot modes by dedicated boot mode pins.

For functional details see  ug1085 - Zynq UltraScale+ TRM (Boot Modes Section).

Signals, Interfaces and Pins

Board to Board (B2B) connectors

The TE0807 MPSoC SoM has four Board to Board (B2B) connectors with 160 contacts per connector.

Each connector has a specific arrangement of the signal pins, which are grouped together in categories related to their functionalities and to their belonging to particular units of the Zynq UltraScale+ MPSoC like I/O banks, interfaces and Gigabit transceivers
or to the on-board peripherals.

Following table lists the I/O-bank signals, which are routed from the MPSoC's PL and PS banks as LVDS pairs or single ended I/O's to the B2B connectors.

BankTypeB2B ConnectorSchematic Names / Connector PinsI/O Signal CountLVDS PairsVCCO Bank VoltageNotes
47HDJ3

B47_L1_P ... B47_L12_P
B47_L1_N ... B47_L12_N

24 I/Os12

VCCO47
pins J3-43, J3-44

VCCO max. 3.3V
usable as single-ended I/Os

48HDJ3

B48_L1_P ... B48_L12_P
B48_L1_N ... B48_L12_N

24 I/Os12

VCCO48
pins J3-15, J3-16

VCCO max. 3.3V
usable as single-ended I/Os

64HPJ4

B64_L1_P ... B64_L24_P
B64_L1_N ... B64_L24_N

B_64_T0 ... B_64_T3

52 I/O's24

VCCO64
pins J4-58, J4-106

VCCO max. 1.8V
usable as single-ended I/Os

65HPJ4

B65_L1_P ... B65_L24_P
B65_L1_N ... B65_L24_N

B_65_T0 ... B_65_T3

52 I/Os24

VCCO65
pins J4-69, J4-105

VCCO max. 1.8V
usable as single-ended I/Os

66HPJ1

B66_L1_P ... B66_L24_P
B66_L1_N ... B66_L24_N

B_66_T0 ... B_66_T3

48 I/Os24

VCCO66
pins J1-90, J1-120

VCCO max. 1.8V
usable as single-ended I/Os

500MIOJ3MIO13 ... MIO2513 I/Os-PS_1V8User configurable I/Os on B2B
501MIOJ3MIO26 ... MIO5126 I/Os-PS_1V8User configurable I/Os on B2B
502MIOJ3MIO52 ... MIO7726 I/Os-PS_1V8User configurable I/Os on B2B

Table 4: B2B connector pin-outs of available PL and PS banks of the TE0807-01 SoM.

All MIO banks are powered from on-module DC-DC power rail. All PL I/O Banks have separate VCCO pins in the B2B connectors, valid VCCO should be supplied from the baseboard.

For detailed information about the B2B pin-out, please refer to the Pin-out table. 

The configuration of the I/O's MIO13 - MIO77 are depending on the base-board peripherals connected to these pins.

MGT Lanes

The Xilinx Zynq UltraScale+ MPSoC device used on the TE0807 module has 20 high-speed data lanes (Xilinx GTH / GTR transceiver). All of them are wired directly to B2B connector. MGT (Multi Gigabit Transceiver) lane consists of one transmit and one receive (TX/RX) differential pairs, four signals total per one MGT lane. Following table lists lane number, MGT bank number, transceiver type, signal schematic name, board-to-board pin connection and FPGA pins connection:

BankTypeLaneSignal NameB2B PinFPGA Pin
228GTH0
  • B505_RX0_P
  • B505_RX0_N
  • B505_TX0_P
  • B505_TX0_N
  • JM3-26
  • JM3-28
  • JM3-25
  • JM3-27
  • PS_MGTRRXP0_505, F27
  • PS_MGTRRXN0_505, F28
  • PS_MGTRTXP0_505, E25
  • PS_MGTRTXN0_505, E26
1


2


3


229GTH0
  • B505_RX1_P
  • B505_RX1_N
  • B505_TX1_P
  • B505_TX1_N
  • JM3-20
  • JM3-22
  • JM3-19
  • JM3-21
  • PS_MGTRRXP1_505, D27
  • PS_MGTRRXN1_505, D28
  • PS_MGTRTXP1_505, D23
  • PS_MGTRTXN1_505, D24
1


2


3


230GTH0
  • B505_RX2_P
  • B505_RX2_N
  • B505_TX2_P
  • B505_TX2_N
  • JM3-14
  • JM3-16
  • JM3-13
  • JM3-15
  • PS_MGTRRXP0_505, B27
  • PS_MGTRRXN0_505, B28
  • PS_MGTRTXP0_505, C25
  • PS_MGTRTXN0_505, C26
1


2


3


128GTH0
  • B505_RX3_P
  • B505_RX3_N
  • B505_TX3_P
  • B505_TX3_N
  • JM3-8
  • JM3-10
  • JM3-7
  • JM3-9
  • PS_MGTRRXP1_505, A25
  • PS_MGTRRXN1_505, A26
  • PS_MGTRTXP1_505, B23
  • PS_MGTRTXN1_505, B24
1


2


3


505GTR0


1


2


3


Table 4: MGT lanes


There are 3 clock sources for the GTR transceivers. B505_CLK0 is connected directly to B2B connector JM3, so the clock can be provided by the carrier board. Clocks B505_CLK1 and B505_CLK3 are provided by the on-board clock generator (U10). As there are no capacitive coupling of the data and clock lines that are connected to the connectors, these may be required on the user’s PCB depending on the application.

Clock signalBankSourceFPGA PinNotes
B505_CLK0_P505B2B, JM3-31PS_MGTREFCLK0P_505, F23Supplied by the carrier board
B505_CLK0_N505B2B, JM3-33PS_MGTREFCLK0N_505, F24Supplied by the carrier board
B505_CLK1_P505U10, CLK2APS_MGTREFCLK1P_505, E21On-board Si5338A
B505_CLK1_N505U10, CLK2BPS_MGTREFCLK1N_505, E22On-board Si5338A
B505_CLK2_P505N/APS_MGTREFCLK2P_505, C21Not connected
B505_CLK2_N505N/APS_MGTREFCLK2N_505, C22Not connected
B505_CLK3_P505U10, CLK1APS_MGTREFCLK3P_505, A21On-board Si5338A
B505_CLK3_N505U10, CLK1BPS_MGTREFCLK3N_505, A22On-board Si5338A

Table 5: MGT reference clock sources

JTAG Interface

JTAG access is provided through the MPSoC's PS configuration bank 503 with bank voltage PS_1V8.

JTAG SignalB2B Connector Pin
TCKJ2-120
TDIJ2-122
TDOJ2-124
TMSJ2-126

Table 4: B2B connector pin-out of JTAG interface.

Configuration Bank Control Signals

The Xilinx Zynq UltraScale+ MPSoC's PS configuration bank 503 control signal pins are accessible through B2B connector J2.

For further information about the particular control signals and how to use and evaluate them, refer to the  Xilinx Zynq UltraScale+ MPSoC TRM and UltraScale Architecture Configuration - User Guide.

SignalB2B Connector PinFunction
DONEJ2-116PL configuration completed.
PROG_BJ2-100PL configuration reset signal.
INIT_BJ2-98PS is initialized after a power-on reset.
SRST_BJ2-96System reset.
MODE0 ... MODE3J2-109/J2-107/J2-105/J2-103

4-bit boot mode pins.

For further information about the boot modes refer to the Xilinx Zynq UltraScale+ MPSoC TRM section 'Boot and Configuration'.

ERR_STATUS / ERR_OUTJ2-86 / J2-88

ERR_OUT signal is asserted for accidental loss of power, an error, or an exception in the MPSoC's Platform Management Unit (PMU).

ERR_STATUS indicates a secure lock-down state.

PUDC_BJ2-127Pull-up during configuration (pulled-up to PL_1V8).

Table 5: B2B connector pin-out of MPSoC's PS configuration bank.

Analog Input

The Xilinx Zynq UltraScale+ MPSoC provides differential pairs for analog input values. The pins are exposed to B2B-connector J2.

SignalB2B Connector PinFunction
V_P, V_NJ2-113, J2-115System Monitor
DX_P, DX_NJ2-119, J2-121Temperature-sensing diode pins

Table 6: B2B connector pin-out of analog input pins

Quad SPI Interface

Quad SPI Flash memory ICs U7 and U17 are connected to the Zynq MPSoC PS QSPI0 interface via PS MIO bank 500, pins MIO0 ... MIO5 and MIO7 ... MIO12.

MIOSignal NameU7 Pin
MIOSignal NameU17 Pin
0SPI Flash CLKB2
7SPI Flash CS
C2
1SPI Flash IO1
D2
8SPI Flash IO0
D3
2SPI Flash IO2
C4
9SPI Flash IO1
D2
3SPI Flash IO3D4
10SPI Flash IO2
C4
4SPI Flash IO0
D3
11SPI Flash IO3D4
5SPI Flash CS
C2
12SPI Flash CLK
B2

Table 7: PS MIO pin assignment of the Quad SPI Flash memory ICs.

Default PS MIO Mapping

PS MIOFunctionB2B PinConnected toPS MIOFunctionB2B PinConnected to
0SPI0-U7-B2, CLK40..45--Not connected
1SPI0-U7-D2, DO/IO1
46SDJM1-17B2B, SD_DAT3
2SPI0-U7-C4, WP/IO2
47SD

JM1-19

B2B, SD_DAT2
3SPI0-U7-D4, HOLD/IO348SD

JM1-21

B2B, SD_DAT1
4SPI0-U7-D3, DI/IO0 49SDJM1-23B2B, SD_DAT0
5SPI0- U7-C2, CS50SDJM1-25B2B, SD_CMD
6N/A-Not connected51SDJM1-27B2B, SD_CLK
7SPI1-U17-C2, CS52USB_PHY-U18-31, OTG-DIR
8SPI1-U17-D3, DI/IO053USB_PHY-U18-31, OTG-DIR
9SPI1-U17-D2, DO/IO154USB_PHY-U18-5, OTG-DATA2
10SPI1-U17-C4, WP/IO255USB_PHY-U18-2, OTG-NXT
11SPI1-U17-D4, HOLD/IO356USB_PHY-U18-3, OTG-DATA0
12SPI1-U17-B2, CLK57USB_PHY-U18-4, OTG-DATA1
13..20eMMC-U6, MMC-D0..D758USB_PHY-U18-29, OTG-STP
21eMMC-U6, MMC-CMD59USB_PHY-U18-6, OTG-DATA3
22eMMC-U6, MMC-CLKR60USB_PHY-U18-7, OTG-DATA4
23eMMC-U6, MMC-RST61USB_PHY-U18-9, OTG-DATA5
24ETH-U8, ETH-RST62USB_PHY-U18-10, OTG-DATA6
25USB_PHY-U18, OTG-RST

63

USB_PHY-U18-13, OTG-DATA7
26MIOJM1-95B2B, as PJTAG MIO possible64ETH-U8-53, ETH-TXCK
27MIOJM1-93B2B, as PJTAG MIO possible65..66ETH-U8-50..51, ETH-TXD0..1
28MIOJM1-99B2B, as PJTAG MIO possible67..68ETH-U8-54..55, ETH-TXD2..3
29MIOJM1-99B2B, as PJTAG MIO possible69ETH-U8-56, ETH-TXCTL
30MIOJM1-92B2B (UART RX)70ETH-U8-46, ETH-RXCK
31MIOJM1-85B2B (UART TX)71..72ETH-U8-44..45, ETH-RXD0..1
32MIOJM1-91B2B73..74ETH-U8-47..48, ETH-RXD2..3
33MIOJM1-87B2B75ETH-U8-43, ETH-RXCTL
34..37--Not connected76ETH-U8-7, ETH-MDC
38I2C-U10-12, SCL77ETH-U8-8, ETH-MDIO
39I2C-U10-19, SDA----

Table 8: TE0807-01 PS MIO mapping

On-board Peripherals

Flash

The TE0808 SoM can be configured with max. 512 MByte Flash memory for configuration and operation.

 NameICDesignatorPS7MIONotes
SPI FlashN25Q256A11E1240EU7QSPI0MIO0 ... MIO5dual parallel booting possible, 32 MByte memory per Flash IC at standard configuration
SPI FlashN25Q256A11E1240EU17QSPI0MIO7 ... MIO12as above

Table 10: Peripherals connected to the PS MIO pins.

DDR4 SDRAM

The TE0807-01 SoM is equipped with with four DDR4-2400 SDRAM modules with up to 8 GByte memory density. The SDRAM modules are connected to the Zynq MPSoC's PS DDR controller (bank 504) with a 64-bit data bus.

Refer to the Xilinx Zynq UltraScale+ datasheet DS925 for more information on whether the specific package of the Zynq UltraScale+ MPSoC supports the maximum data transmission rate of 2400 MByte/s.

Programmable PLL Clock Generator

Following table illustrates on-board Si5345A programmable clock multiplier chip inputs and outputs:

InputConnected toFrequencyNotes
IN0On-board Oscillator (U25)25.000000 MHz-
IN1B2B Connector pins J2-4, J2-6 (differential pair)UserAC decoupling required on base
IN2B2B Connector pins J3-66, J3-68 (differential pair)UserAC decoupling required on base
IN3OUT9UserLoop-back from OUT9
OutputConnected toFrequencyNotes
OUT0B2B Connector pins J2-3, J2-1 (differential pair)UserDefault off
OUT1B230 CLK0UserDefault off
OUT2B229 CLK1UserDefault off
OUT3B228 CLK1UserDefault off
OUT4B505 CLK2UserDefault off
OUT5B505 CLK3UserDefault off
OUT6B128 CLK0UserDefault off
OUT7B2B Connector pins J2-7, J2-9 (differential pair)UserDefault off
OUT8B2B Connector pins J2-13, J2-15 (differential pair)UserDefault off
OUT9IN3 (Loop-back)UserDefault off
XA/XBQuartz (Y1)50.000 MHz-

Table 11: Programmable PLL clock generator input/output.


The Si5345A programmable clock generator's control interface pins are exposed to B2B connector J2. For further information refer to the Si5345A data sheet.

SignalB2B Connector PinFunction
PLL_FINCJ2-81Frequency increment.
PLL_LOLNJ2-85Loss of lock (active-low).
PLL_SEL0 / PLL_SEL1J2-93 / J2-87Manual input switching.
PLL_FDECJ2-94Frequency decrement.
PLL_RSTJ2-59

Device reset (active-low)

PLL_SCL / PLL_SDAJ2-90 / J2-92

I2C interface, external pull-ups needed for SCL / SDA lines.

I2C address in current configuration: 1101000b.

Table 12: B2B connector pin-out of Si5345A programmable clock generator.

Note

Si5345 OTP ROM is not programmed by default at delivery, so it is customers responsibility to either configure Si5345 during FSBL or then use SiLabs programmer and program the OTP ROM with customer fixed clock setup.

Si5345 OTP can only be programmed two times, as different user configurations may required different setup TE0808 is normally shipped with blank OTP.
For more information refer to Si5345 at SiLabs.

Oscillators

The TE0808-04 SoM is equipped with two on-board oscillators to provide the Zynq's MPSoC's PS configuration bank 503 with reference clock signals.

ClockFrequencyBank 503 PinConnected to
PS_CLK33.333333 MHzP20MEMS Oscillator, U32
PS_PAD (RTC)32.768 kHzR22/R23Quartz crystal, Y2

Table 13: Reference clock-signals to PS configuration bank 503.

On-board LEDs

LED

ColorConnected toDescription and Notes
D1RedDONE signal (PS Configuration Bank 503)This LED goes ON when power has been applied to the module and
stays ON until MPSoC's programmable logic is configured properly.

Table 14: LED's description.

Power and Power-On Sequence

Power Consumption

The maximum power consumption of a module mainly depends on the design which is running on the FPGA.

Xilinx provide a power estimator excel sheets to calculate power consumption. It's also possible to evaluate the power consumption of the developed design with Vivado. See also Trenz Electronic Wiki FAQ.

Power Input PinTypical Current
DCDCINTBD*
LP_DCDCTBD*
PL_DCINTBD*
PS_BATTTBD*

Table 15: Maximum current of power supplies. *to be determined soon with reference design setup.

Power supply with minimum current capability of 3A for system startup is recommended. For the lowest power consumption and highest efficiency of on board DC/DC regulators it is recommended to powering the module from one single 3.3V supply. Except 'PS_BATT', all input power supplies have a nominal value of 3.3V. Although the input power supplies can be powered up in any order, it is recommended to power them up simultaneously.

The TE0808 module equipped with the Xilinx Zynq UltraScale+ MPSoC delivers a heterogeneous multi-processing system with integrated programmable logic and independently operable elements and is designed to meet embedded system power management requirement by advanced power management features. This features allow to offset the power and heat constraints against overall performance and operational efficiency.

This features allowing highly flexible power management are achieved by establishing Power Domains for power isolation. The Zynq UltraScale+ MPSoC has multiple power domains, whereby each power domain requires its own particular external DC-DC converters.

The Processing System contains three Power Domains:

  • Battery Power Domain (BBRAM and RTC)
  • Full-Power Domain (Application Processing Unit, DDR Controller, Graphics Processing Unit and High-Speed Connectivity)
  • Low-Power Domain (Real-Time Processing Unit, Security and Configuration Unit, Platform Management Unit, System Monitor and General Connectivity)

The fourth Power Domain is for the Programmable Logic (PL). If individual Power Domain control is not required, power rails can be shared between domains.

On the TE0808-04 SoM, following power domains can be powered up individually with power rails available on the B2B connectors:

  • Full-power domain, supplied by power rail DCDCIN
  • Low-power domain, supplied by power rail LP_DCDC
  • Programmable logic, supplied by power rail PL_DCIN
  • Battery power domain, supplied by power rail PS_BATT

Each power domain has its own enable and power good signals. The power rail GT_DCDC is needed to generate the voltages for the Multi Gigabit Transceiver units of the Zynq UltraScale+ MPSoC.

Power Distribution Dependencies

The power rails DCDCIN, LP_DCDC, PL_DCIN, PS_BATT have to be powered up on the assigned pins of the B2B connectors as listed on the section "Power Rails". Except 'PS_BATT' (see section "Recommended Operation Conditions"), all power-rails can be powered from 3.3V power sources (also share the same source, if power domain control is not required).

There are following dependencies how the initial voltages of the power rails on the B2B connectors are distributed to the on-board DC-DC converters, which power up further DC-DC converters and the particular on-board voltages:


Scroll Title
anchorFigure_3
titleFigure 3: TE0807-01 Power Distribution Diagram
Scroll Ignore


Scroll Only



See also Xilinx datasheet DS925 for additional information. User should also check related base board documentation when intending base board design for TE0807 module.

Power-On Sequence

The TE0807 SoM meets the recommended criteria to power up the Xilinx Zynq UltraScale+ MPSoC properly by keeping a specific sequence of enabling the on-board DC-DC converters dedicated to the particular Power Domains and powering up the on-board voltages.

The on-board voltages of the TE0808 SoM will be powered-up in order of a determined sequence by activating the above-mentioned power rails and the Enable-Signals of the DC-DC converters. The on-board voltages will be powered up at three steps.

  1. Low-Power Domain (LPD) and on-board Si5345A programmable clock generator supply voltage
  2. Programmable Logic (PL) and Full-Power Domain (FPD)
  3. GTH, PS GTR transceiver and DDR memory

Hence, those three power instances will be powered up consecutively and the Power-Good-Signals of the previous instance has to be asserted.

Following diagram describes the sequence of enabling the three power instances utilizing the DC-DC converter control signals (Enable, Power-Good), which will power-up in descending order as listed in the blocks of the diagram.


Scroll Title
anchorFigure_4
titleFigure 4: TE0807-01 Power-on Sequence Diagram
Scroll Ignore


Scroll Only


Operation Conditions of the DC-DC Converter Control Signals

The control signals have to be asserted on the B2B connector J2, whereby some of the Power-Good signals need external pull-up resistors.

Enable-SignalB2B Connector PinMax. VoltageNote
Power-Good-SignalB2B Connector PinPull-up ResistorNote
EN_LPDJ2-1086VTPS82085SIL data sheet
LP_GOODJ2-1064K7, pulled up to LP_DCDC-
EN_FPDJ2-102DCDCINNC7S08P5X data sheet
PG_FPDJ2-1104K7, pulled up to DCDCIN-
EN_PLJ2-101PL_DCINleft floating for logic high
(drive to GND for logic low)

PG_PLJ2-104External pull-up needed (max. voltage GT_DCDC),
max. sink current 1 mA

TPS82085SIL /
NC7S08P5X data sheet

EN_DDRJ2-112DCDCINNC7S08P5X data sheet
PG_DDRJ2-1144K7, pulled up to DCDCIN-
EN_PSGTJ2-84DCDCINNC7S08P5X data sheet
PG_PSGTJ2-82External pull-up needed (max. 5.5V),
max. sink current 1 mA
TPS74801 data sheet
EN_GT_RJ2-95GT_DCDCNC7S08P5X data sheet
PG_GT_RJ2-91External pull-up needed (max. 5.5V),
max. sink current 1 mA
TPS74401 data sheet
EN_GT_LJ2-79GT_DCDCNC7S08P5X data sheet
PG_GT_LJ2-97External pull-up needed (max. 5.5V),
max. sink current 1 mA
TPS74801 data sheet
EN_PLL_PWRJ2-776VTPS82085SIL data sheet
PG_PLL_1V8J2-80External pull-up needed (max. 5.5V),
max. sink current 1 mA
TPS82085SIL data sheet

Table 16: Recommended operation conditions of DC-DC converter control signals.

Warning
To avoid any damage to the MPSoC module, check for stabilized on-board voltages in steady state before powering up the MPSoC's I/O bank voltages VCCOx. All I/Os should be tri-stated during power-on sequence.

Core voltages and main supply voltages have to reach stable state and their "Power Good"-signals have to be asserted before other voltages like bank's I/O voltages (VCCOx) can be powered up.

It is important that all PS and PL I/Os are tri-stated at power-on until the "Power Good"-signals are high, meaning that all on-module voltages have become stable and module is properly powered up.

See Xilinx datasheet DS925 for additional information. User should also check related base board documentation when intending base board design for TE0808 SoM.

Voltage Monitor Circuit

The voltages LP_DCDC and LP_0V85 are monitored by the voltage monitor circuit U41, which generates the POR_B reset signal at power-on. A manual reset is also possible by driving the MR-pin (J2-83) to GND. Leave this pin unconnected or connect to VDD (LP_DCDC) when unused.

Scroll Title
anchorFigure_5
titleFigure 5: TE0784-01 Voltage Monitor Circuit
Scroll Ignore


Scroll Only


Power Rails

Power Rail Name

B2B J1 PinsB2B J2 PinsB2B J3 Pins

Directions

Note
PL_DCIN151, 153, 157, 159--Input-
DCDCIN

-

154, 156, 158, 160,
153, 155, 157, 159

-Input-
LP_DCDC-138, 140, 142, 144-Input-
PS_BATT-125-Input-
GT_DCDC--157, 158, 159, 160Input-
PLL_3V3--152InputU5 (programmable PLL)
3.3V nominal input
SI_PLL_1V8--151OutputInternal voltage level
1.8V nominal output
PS_1V8-99147, 148Output

Internal voltage level
1.8V nominal output

PL_1V891, 121--Output

Internal voltage level
1.8V nominal output

DDR_1V2-135-Output

Internal voltage level
1.2V nominal output

Table 16: TE0807-01 power rails

Bank Voltages

BankTypeSchematic Name / B2B Connector PinsVoltageReference Input VoltageVoltage Range
47HDVCCO47, pins J3-43, J3-44user-max. 3.3V
48HDVCCO48, pins J3-15, J3-16user-max. 3.3V
64HPVCCO64, J4-58, J4-106userVREF_64, pin J4-88max. 1.8V
65HPVCCO65, J4-69, J4-105userVREF_65, pin J4-15max. 1.8V
66HPVCCO66, J1-90, J1-120userVREF_66, pin J1-108max. 1.8V
500MIOPS_1V81.8V--
501MIOPS_1V81.8V--
502MIOPS_1V81.8V--
503CONFIGPS_1V81.8V--

Table 17: TE0807-01 I/O bank voltages

See Xilinx Zynq UltraScale+ datasheet DS925 for the voltage ranges allowed.

Board to Board Connectors

Include Page
5.2 x 7.6 UltraSoM+ ST5 and SS5 B2B Connectors
5.2 x 7.6 UltraSoM+ ST5 and SS5 B2B Connectors

Variants Currently In Production

Trenz shop TE0807 overview page
English pageGerman page

Technical Specifications

Absolute Maximum Ratings

Parameter

MinMax

Unit

Notes / Reference Document

PL_DCIN-0.37VTPS82085SIL / EN63A0QI data sheet
DCDCIN-0.37VTPS82085SIL / TPS51206 data sheet
LP_DCDC-0.34VTPS3106K33DBVR data sheet
GT_DCDC-0.37VTPS82085SIL data sheet
PS_BATT-0.52VXilinx DS925 data sheet
PLL_3V3-0.53.8VSi5345/44/42 data sheet
VCCO for HD I/O banks-0.53.4VXilinx DS925 data sheet
VCCO for HP I/O banks-0.52VXilinx DS925 data sheet
VREF-0.52VXilinx DS925 data sheet
I/O input voltage for HD I/O banks-0.55VCCO + 0.55VXilinx DS925 data sheet
I/O input voltage for HP I/O banks-0.55VCCO + 0.55VXilinx DS925 data sheet
PS I/O input voltage (MIO pins)-0.5VCCO_PSIO + 0.55VXilinx DS925 data sheet,
VCCO_PSIO 1.8V nominally

Receiver (RXP/RXN) and transmitter
(TXP/TXN) absolute input voltage

-0.51.2VXilinx DS925 data sheet

Voltage on input pins of
NC7S08P5X 2-Input AND Gate

-0.5VCC + 0.5VNC7S08P5X data sheet,
see schematic for VCC

Voltage on input pins (nMR) of
TPS3106K33DBVR Voltage Monitor, U41

-0.3VDD + 0.3V

TPS3106 data sheet,
VDD = LP_DCDC

"Enable"-signals on TPS82085SIL
(EN_PLL_PWR, EN_LPD)
-0.37VTPS82085SIL data sheet

Storage temperature (ambient)

-40

100

°C

ROHM Semiconductor SML-P11 Series data sheet

Table 18: Module absolute maximum ratings

Note
Assembly variants for higher storage temperature range are available on request.

Recommended Operating Conditions

ParameterMinMaxUnitNotes / Reference Document
PL_DCIN2.56VEN63A0QI / TPS82085SIL data sheet
DCDCIN3.16VTPS82085SIL / TPS51206PSQ data sheet
LP_DCDC2.53.6VTPS82085SIL / TPS3106 data sheet
GT_DCDC2.56VTPS82085SIL data sheet
PS_BATT1.21.5VXilinx DS925 data sheet
PLL_3V33.143.47VSi5345/44/42 data sheet
3.3V typical
VCCO for HD I/O banks1.143.4VXilinx DS925 data sheet
VCCO for HP I/O banks0.951.9VXilinx DS925 data sheet
I/O input voltage for HD I/O banks.-0.2VCCO + 0.2VXilinx DS925 data sheet
I/O input voltage for HP I/O banks-0.2VCCO + 0.2VXilinx DS925 data sheet
PS I/O input voltage (MIO pins)-0.2VCCO_PSIO + 0.2VXilinx DS925 data sheet,
VCCO_PSIO 1.8V nominally
Voltage on input pins of
NC7S08P5X 2-Input AND Gate
0VCCV

NC7S08P5X data sheet,
see schematic for VCC

Voltage on input pin 'MR' of
TPS3106K33DBVR Voltage Monitor, U41

0VDDV

TPS3106 data sheet,
VDD = LP_DCDC

Table 19: Recommended operating conditions

Module operating temperature range depends also on customer design and cooling solution. Please contact us for options.

Note
See Xilinx datasheet DS925 for more information about absolute maximum and recommended operating ratings for the Zynq UltraScale+ chips.

Physical Dimensions

  • Module size: 52 mm × 76 mm.  Please download the assembly diagram for exact numbers

  • Mating height with standard connectors: 4mm

  • PCB thickness: 1.6mm

  • Highest part on PCB: approx. 3mm. Please download the step model for exact numbers

All dimensions are given in millimeters.

Scroll Title
anchorFigure_6
titleFigure 6: Module physical dimensions drawing


Revision History

Hardware Revision History

DateRevision

Notes

PCN LinkDocumentation Link
-01current available module revision-TE0807-01

Table 20: Hardware revision history table


Scroll Title
anchorFigure_7
titleFigure 7: Module hardware revision number


Document Change History

HTML
<!--
Generate new entry:
1.add new row below first
2.Copy "Page Information Macro(date)" Macro-Preview, Metadata Version number, Author Name and description to the empty row. Important Revision number must be the same as the Wiki document revision number
3.Update Metadata = "Page Information Macro (current-version)" Preview+1 and add Author and change description.
  -->


Date

Revision

Contributors

Description

Page info
modified-date
modified-date
dateFormatyyyy-MM-dd

Page info
infoTypeCurrent version
dateFormatyyyy-MM-dd
typeFlat

Page info
infoTypeModified by
dateFormatyyyy-MM-dd
typeFlat

  • initial document

Table 21: Document change history

Disclaimer

Include Page
IN:Legal Notices
IN:Legal Notices

Image RemovedImage RemovedImage Removed