Download PDF version of this document.

Table of Contents

Overview

The Trenz Electronic TEP0003 is is a BEMF (Back Electromagnetic Field) based drive. It can be used in many low cost drives where no low speed operation is needed.

Refer to http://trenz.org/tep0003-info for the current online version of this manual and other available documentation.

Key Features

  • Modules/ SoC FPGA
    • Compatible with Digilent's Pmod interfaces

  • RAM/Storage
  • On Board
    • 2x A2D Converters
    • 3x Current Sensors
    • 6x Power Stages
  • Interface
    • 2x Pmod Pin Headers (2x6 Pol)
  • Power 
    •  3.3V supply voltage from Pmods
  • Dimension
    • 40 mm x 40 mm

Block Diagram

TEP0003 block diagram

Main Components

TEP0003 main components
  1. Pmod Pin Header, J1
  2. Pmod Pin Header, J2
  3. Synchronous DC/DC Converter, U7
  4. Power Stages, U1...U6
  5. Current Sensors, U18, U21, U46
  6. ADC, U22, U47
  7. Terminal Block, J3
  8. Terminal Block, J4
  9.  Low-Power Push-Pull Output Comparator, U9

Initial Delivery Stat

Storage device name

Content

Notes

--


--

--

Initial delivery state of programmable devices on the module

Configuration Signals

Signals, Interfaces and Pins

Pmod Connectors

TEP0003 is equipped with two Pmod Connectors. 

PinSchematicNotes
Pmod, J1Pmod, J2
1PWM_CH0ADC_CH
2PWM_CH1ADC_SCK
3PWM_CH2ADC_CS
4-SENSOR_FAUL
5GNDGND
63.3V3.3V
7COMP_CH0ADC0_DO
8COMP_CH1ADC1_DO
9COMP_CH2-
10--
11GNDGND
123.3V3.3V
General PL I/O to B2B connectors information

Terminal blocks

The TEP0002 is equipped with two Terminal Blocks J3 and J4.

DesignatorPinSchematicNotes
J31DRV_CH2ARK500-3
2DRV_CH1ARK500-3
3DRV_CH0ARK500-3
J41DC_INARK500-2
2GNDARK500-2
Terminal Blocks information

On-board Peripherals

Chip/InterfaceDesignatorNotes
ADCU22, U47
On board peripherals

Analog to Digital Converters

The TEP0003 has two ADCs, U22 and U47. 

PinsConnected to
ADC, U22ADC, U47Notes
AVDD5V5V
REF5V5V
AIN0+U18 (VIOUT)DC_IN
AIN0-GNDGND
AIN1+U21 (VIOUT)U46 (VIOUT)
AIN1-GNDGND
REFGNDGNDGND
DVDD3.3V3.3V
SCLKADC_SCKADC_SCKAccess via Pmod, J2
SDOADC1_DOADC0_DOAccess via Pmod, J2
CSADC_CSADC_CSAccess via Pmod, J2
CH_SELADC_CHADC_CHAccess via Pmod, J2
PDENGNDGND
Analog Digital Converter


Power and Power-On Sequence

Power Supply

TEP0003 will be power supplied through 3.3V from Pmods, J1 and J2.

Power Consumption

Power Input PinTypical Current
3.3VTBD*
Power Consumption

* TBD - To Be Determined

Power Distribution Dependencies

Power Distribution

Power-On Sequence

There is no specific power on sequence, after power on all electrical components will be enabled. 

Power Rails

Power Rail Name

Pmod J1 Pin

Pmod J2 Pin

Notes
3.3V6,126,12
Module power rails.

Technical Specifications

Absolute Maximum Ratings

SymbolsDescriptionMinMaxUnit
3.3VSupply Voltage-0.36.5V
T_STGStorage Temperature-40105°C
PS absolute maximum ratings

Recommended Operating Conditions

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

ParameterMinMaxUnitsReference Document
3.3V3.04.2VSupplied from Pmod
T_OPR-30+105°CSee ARK500-3 and ARK500-2 Datasheet
Recommended operating conditions.

Physical Dimensions

  • Module size: 40 mm × 40 mm.  Please download the assembly diagram for exact numbers.

PCB thickness: 1.6 mm.

Physical Dimension

Currently Offered Variants 

Trenz shop TEP0003 overview page
English pageGerman page
Trenz Electronic Shop Overview

Revision History

Hardware Revision History


DateRevisionChangesDocumentation Link
2018-07-1801
  • Initial Release
REV01
Hardware Revision History

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Board hardware revision number.

Document Change History

DateRevisionContributorDescription

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • Initial Release

--

all

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • --
Document change history.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy244.$Proxy3589#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • No labels