Affected Product | Effected Changes | Status* | CPLD | Change Log current development state | Link to current firmware description |
---|
TEM0007 | #? | Unprocessed | LCMXO2-256HC |
| currently not available |
TE0710 | #? | Unprocessed | LCMXO2-256HC |
| TE0710 CPLD |
TE0711 | #1,#2,#3,#4,#5,#6 | Processing | LCMXO2-256HC | Signals are renamed according to the schematic. NOSEQ pin is added. PGOOD(STAT_SC2) pulled up. JTAG signals timing corrected. LED function changed MODE_SC1 is connected to LED I2C to GPIO slave added CPLD_REVISION as generic parameter added NOSEQ_SC4 and STAT_SC2 defined as INOUT Pulled up or pulled down ports was controlled according to CPLD IO standardization. UIO and UI_CLK pins defined as I2C pins. But UIO and ULF functions are as before.
| TE0711 CPLD |
TE0712 | #1,#3,#4,#5,#6 | Test phase | LCMXO2-256HC | Renaming the port signals according to the schematic. Defining and reading CPLD Revision via I2C interface. JTAG signal timing adjustment Adding I2C to gpio ip (i2c_slave.vhd) LED function was changed.
| TE0712 CPLD |
TE0713 | #1,#2,#3,#4,#5,#6 | Processing | LCMXO2-256HC | I2C to GPIO added to communicate with FPGA Signals are renamed adccording to the schematic. NOSEQ pin added. CPLD_REVISION as generic parameter added. PGOOD and NOSEQ pins pulled up. JTAG signals timing corrected.
| TE0713 CPLD |
TE0715 | #1,#2,#3,#4,#5,#6 | Released | LCMXO2-256HC | - Boot mode configuration via hardware (dip switch) and firmware added (Boot mode configuration via linux console)
- Pullup or pulldown states of PORT pins was checked.
- Adding i2c to gpio ip (i2c_slave.vhd)
- Changing oscillator frequency from 12.09 MHZ to 24.18MHZ
- PORT signals according to the schematic are renamed.
- JTAG time constraint correction
- PGOOD pin is used as boot mode selector pin.
- VCFG1 (MIO8) pin can be changed by i2cset command. This pin must be grounded by boundary scaning.Refer to the following site :https://support.xilinx.com/s/article/57930?language=en_US
| TE0715 CPLD |
TE0720 | #1,#2,#5,#6,#7 (#4 since CPLD Rev06) | Released | LCMXO2-1200HC | - Added matched functions for WDT Chip BD39040MUF-CE2
- PG_ALL pin pulled up.
- User can activate WDT as before.
- If no WDT chip on the board, hardware WDT will be switched automatically on software WDT with PL clock input (X6 pin of CPLD and K20 of FPGA).
- If no WDT chip on the board, software WDT will work with CR1(14) clock input as before.
- If WDT chip on the board, hardware and software WDT work separately with PL input clock (X6 pin) for hardware WDT and CR1(14) as input clock for software WDT.
- For software WDT : phytool write eth0/0x1A/7 0xA500
- For hardware WDT : phytool write eth0/0x1A/7 0xB600
- Using CR5[15:14] to save the WDT status ("00" WDT deactive, "01" Hardware WDT, "10" Software WDT, "11" No WDT chip on the board, software WDT with PL clock input)
- Using Register4 of mdio_slave_interface to see WDT status via FSBL code (first test in vivado 20.2 and vivado 21.2) or following instruction in linux: phytool read eth0/0x1A/4
- Boot mode configuration via MDIO interface (phytool)
- PGOOD pin is used as boot mode selector pin.
- NOSEQ pin is used as tristate via i2c interface.
- Reseting the FPGA after boot mode configuration
- Matched to FSBL code to show all informations while booting in linux console. For example Boot mode, pudc state ...
- Monitoring CR4[15:8] and CR5[10] continuously, to implement a state machine for boot mode configuration correctly.
- Using CR4[15:12] as control bit to reset FPGA
- Using CR4[9:8] as boot mode configuration , if the FPGA is not restarted still via soft reset.
- Defining a new input register for mdio_slave_interface (CR5)
- Using CR5[9:8] as boot mode configuration, if the FPGA is restarted already via soft reset.
- Using CR5[10] to monitor , if the FPGA is restarted already via soft reset.
- Using Register4 to read the generic parameters and other parameters via FSBl code or phytool command in linux : Phytool read eth0/0x1A/4
- Using i2c_slave.vhd instead of I2C_to_GPIO.v
- Changing Firmware Register MDIO_SL_REGISTER_4_CONTENT to CPLD_REVISION register.
| TE0720 CPLD |
TE0741 | #1,#4,(#5 still in process) | Processing | LCMXO2-256HC | | TE0741 CPLD |
TE0820 | #1,#2,#3,#4,#5,#6 | Released | LCMXO2-256HC | Adding configuration of boot mode in linux console and via generic parameters PGOOD pin used as boot mode selector pin. Adding boot mode configuration via hardware JTAG time constraint correction Adding i2c to gpio ip (i2c_slave.vhd) LED function is changed. New generic parameter defined : PCB_REV EN1 pin
| TE0820 CPLD |
TE0821 | #1,#2,#3,#4,#5,#6 | Processing | LCMXO2-256HC | Adding configuration of boot mode in linux console and via generic parameters PGOOD pin used as boot mode selector pin. Adding boot mode configuration via hardware JTAG time constraint correcture Adding I2C to gpio ip (i2c_slave.vhd) LED function was changed.
| TE0821 CPLD |
TE0823 | #1,#2,#3,#4,#5,#6 | Processing | LCMXO2-256HC | Adding configuration of boot mode in linux console and via generic parameters PGOOD pin used as boot mode selector pin. Adding boot mode configuration via hardware JTAG time constraint correcture Adding I2C to gpio ip (i2c_slave.vhd) LED function was changed.
| TE0823 CPLD |
TE0841 | #? | Unprocessed | LCMXO2-256HC |
| TE0841 CPLD |
TE0701 | #2, #4 | Test phase | LCMXO2-1200HC | - Connecting PGOOD to CM2 to use as boot mode pin selector
- JTAG timing correction
| TE0701 CPLD |
TE0703 | #1,#2,#3,#4,#6 | Released | LCMXO2-1200HC | Oscillator frequency is changed from 12.09 MHz to 24.18 MHZ. Access to CPLD of TE0715 with a generic parameter added. (For optional jed file to access CPLD of TE0715 module) PGOOD used as second boot mode selector pin and connected to dip switch S2-1. PGOOD and MODE are boot mode selector pins. S2-1 dip switch (CM1) functionality is changed.In HW PCB REV0 to REV04 is used for SD card detection but in HW PCB REV05 and REV06 is used to set or reset PGOOD. MIO14 is connected to FTDI_RXD directly without depending on PGOOD. CM1 (Dip switch S2-2) has no effect on MIO9 anymore. That means MIO9 is connected to SD_CD only and not to SD_CD and CM1.
| TE0703 CPLD - CC703S |
TE0705 | #2, #3, #4 | Test phase | LCMXO2-1200HC | Access to CPLD chip of TE0715 USR0 is used as PGOOD, if Access_to_TE0715_CPLD is activated. USR1 is used as JTAGMODE signal of TE0715 CPLD chip. USR1 = ON --> Access to FPGA , USR1 = OFF --> Access to CPLD USR2 is used as selector signal to access to TE0715 CPLD , if Access_to_TE0715_CPLD variable is 2. JTAG Timing correction
| TE0705 CPLD |
TE0706 | #? | HW changes | --- | --- | --- |
TEBA0841 | #? | HW changes | --- | --- | --- |
TEF1002 | #? | Unprocessed | 10M08 |
| TEF1002 SC CPLD MAX10 |
TEB0707 | #? | Unprocessed | 10M08 |
| TEB0707 MAX10 CPLD |