TE0715 Test Board

Overview

Refer to http://trenz.org/te0715-info for the current online version of this manual and other available documentation.

Key Features

• Vitis/Vivado 2020.2
• PetaLinux
• SD
• ETH
• MAC from EEPROM
• USB
• I2C
• RTC
• FMeter
• Modified FSBL (some additional outputs and SI5338 reconfiguration)
• Special FSBL for QSPI Programming

Revision History

Release Notes and Know Issues

Requirements

Software

Hardware

Complete List is available on "<project folder>\board_files\*_board_files.csv"

Design supports following modules:

Design supports following carriers:

Additional HW Requirements:

Content

For general structure and usage of the reference design, see Project Delivery - Xilinx devices

Design Sources

Additional Sources

Prebuilt

Download

Reference Design is only usable with the specified Vivado/Vitis/PetaLinux version. Do never use different Versions of Xilinx Software for the same Project.

Reference Design is available on:

• TE0715 "Test Board" Reference Design

Design Flow

Trenz Electronic provides a tcl based built environment based on Xilinx Design Flow.

See also:

• Xilinx Development Tools
• Vivado Projects - TE Reference Design
• Project Delivery.

The Trenz Electronic FPGA Reference Designs are TCL-script based project. Command files for execution will be generated with "_create_win_setup.cmd" on Windows OS and "_create_linux_setup.sh" on Linux OS.

TE Scripts are only needed to generate the vivado project, all other additional steps are optional and can also executed by Xilinx Vivado/Vitis GUI.  For currently Scripts limitations on Win and Linux OS see: Project Delivery Currently limitations of functionality

1. Run _create_win_setup.cmd/_create_linux_setup.sh and follow instructions on shell:

   _create_win_setup.cmd/_create_linux_setup.sh

   ------------------------Set design paths----------------------------
   -- Run Design with: _create_win_setup
   -- Use Design Path: <absolute project path>
   --------------------------------------------------------------------
   -------------------------TE Reference Design---------------------------
   --------------------------------------------------------------------
   -- (0)  Module selection guide, project creation...prebuilt export...
   -- (1)  Create minimum setup of CMD-Files and exit Batch
   -- (2)  Create maximum setup of CMD-Files and exit Batch
   -- (3)  (internal only) Dev
   -- (4)  (internal only) Prod
   -- (c)  Go to CMD-File Generation (Manual setup)
   -- (d)  Go to Documentation (Web Documentation)
   -- (g)  Install Board Files from Xilinx Board Store (beta)
   -- (a)  Start  design with unsupported Vivado Version (beta)
   -- (x)  Exit Batch (nothing is done!)
   ----
   Select (ex.:'0' for module selection guide):

2. Press 0 and enter to start "Module Selection Guide"
3. Create project and follow instructions of the product selection guide, settings file will be configured automatically during this process.
   

   • optional for manual changes: Select correct device and Xilinx install path on "design_basic_settings.cmd" and create Vivado project with "vivado_create_project_guimode.cmd"

     Note: Select correct one, see also Vivado Board Part Flow

4. Create hardware description file (.xsa file) for PetaLinux project and export to prebuilt folder

   run on Vivado TCL (Script generates design and export files into "<project folder>\prebuilt\hardware\<short name>")

   TE::hw_build_design -export_prebuilt

   Using Vivado GUI is the same, except file export to prebuilt folder.

5. Create and configure your PetaLinux project with exported .xsa-file, see PetaLinux KICKstart
   • use TE Template from "<project folder>\os\petalinux"

   • use exported .xsa file from "<project folder>\prebuilt\hardware\<short name>" . Note: HW Export from Vivado GUI creates another path as default workspace.

   • The build images are located in the "<plnx-proj-root>/images/linux" directory

6. Configure the boot.scr file as needed, see Distro Boot with Boot.scr
   

7. Copy PetaLinux build image files to prebuilt folder

   • copy u-boot.elf, image.ub and boot.scr from "<plnx-proj-root>/images/linux" to prebuilt folder
     

     "<project folder>\prebuilt\os\petalinux\<ddr size>" or "<project folder>\prebuilt\os\petalinux\<short name>"

8. Generate Programming Files with Vitis

   run on Vivado TCL (Script generates applications and bootable files, which are defined in "test_board\sw_lib\apps_list.csv")

   TE::sw_run_vitis -all
   TE::sw_run_vitis (optional; Start Vitis from Vivado GUI or start with TE Scripts on Vivado TCL)

   TCL scripts generate also platform project, this must be done manually in case GUI is used. See Vitis

Launch

Programming

Xilinx documentation for programming and debugging: Vivado/Vitis/SDSoC-Xilinx Software Programming and Debugging

Get prebuilt boot binaries

1. Run _create_win_setup.cmd/_create_linux_setup.sh and follow instructions on shell
2. Press 0 and enter to start "Module Selection Guide"
   1. Select assembly version
   2. Validate selection

   3. Select Create and open delivery binary folder

      Note: Folder "<project folder>\_binaries_<Article Name>" with subfolder "boot_<app name>" for different applications will be generated

QSPI-Boot mode

Optional for Boot.bin on QSPI Flash and image.ub and boot.scr on SD or USB.

1. Connect JTAG and power on carrier with module

2. Open Vivado Project with "vivado_open_existing_project_guimode.cmd" or if not created, create with "vivado_create_project_guimode.cmd"

   run on Vivado TCL (Script programs BOOT.bin on QSPI flash)

   TE::pr_program_flash -swapp u-boot
   TE::pr_program_flash -swapp hello_te0715 (optional)

   To program with Vitis/Vivado GUI, use special FSBL (zynq_fsbl_flash) on setup

3. Copy image.ub and boot.scr on SD or USB
   
   • use files from "<project folder>\_binaries_<Article Name>\boot_linux" from generated binary folder,see: Get prebuilt boot binaries
   • or use prebuilt file location, see "<project folder>\prebuilt\file_location.txt"
4. Set Boot Mode to QSPI-Boot and insert SD or USB.
   • Depends on Carrier, see carrier TRM.

SD-Boot mode

1. Copy image.ub, boot.scr and Boot.bin on SD
   • use files from "<project folder>\_binaries_<Article Name>\boot_linux" from generated binary folder,see: Get prebuilt boot binaries
   • or use prebuilt file location, see "<project folder>\prebuilt\file_location.txt"
   • optional: use startup script init.sh for SD
2. Set Boot Mode to SD-Boot.
   • Depends on Carrier, see carrier TRM.
3. Insert SD-Card in SD-Slot.

JTAG

Not used on this Example.

Usage

1. Prepare HW like described on section TE0715 Test Board#Programming
2. Connect UART USB (most cases same as JTAG)

3. Select SD Card as Boot Mode (or QSPI - depending on step 1)

   Note: See TRM of the Carrier, which is used.

   Starting with Petalinux version 2020.1, the industry standard "Distro-Boot" boot flow for U-Boot was introduced, which significantly expands the possibilities of the boot process and has the primary goal of making booting much more standardised and predictable.
   The boot options described above describe the common boot processes for this hardware; other boot options are possible.
   For more information see Distro Boot with Boot.scr

4. Power On PCB

   boot process

   1. Zynq Boot ROM loads FSBL from SD/QSPI into OCM,

   2. FSBL init PS, programs PL using the bitstream and loads U-boot from SD into DDR,

   3. U-boot loads Linux (image.ub) from SD/QSPI/... into DDR

Linux

1. Open Serial Console (e.g. putty)
   
   • Speed: 115200

   • select COM Port

     Win OS, see device manager, Linux OS see  dmesg |grep tty  (UART is *USB1)

2. Linux Console:
   

   For Linux Login use:

   petalinux login: root
   Password: root

   Note: Wait until Linux boot finished

3. You can use Linux shell now.
   

   i2cdetect -y -r 0	(check I2C 1 Bus)
   dmesg | grep rtc	(RTC check)
   udhcpc				(ETH0 check)
   lsusb				(USB check)

4. Option Features
   • Webserver to get access to Zynq
     • insert IP on web browser to start web interface
   • init.sh scripts
     • add init.sh script on SD, content will be load automatically on startup (template included in "<project folder>\misc\SD")

Vivado HW Manager 

• Monitoring:
  
  • Si5338 CLKs:
    • Set radix from VIO signals to unsigned integer. Note: Frequency Counter is inaccurate and displayed unit is Hz
    • MGT CLK is configured to 125MHz by default, FCLK is not configured by default (optional possible over FSBL → 50MHz on delivered configuration, see FSBL description).

Vivado Hardware Manager

System Design - Vivado

Block Design

Block Design

PS Interfaces

Activated interfaces:

Constrains

Basic module constrains

set_property BITSTREAM.GENERAL.COMPRESS TRUE [current_design]
set_property CONFIG_VOLTAGE 3.3 [current_design]
set_property CFGBVS VCCO [current_design]

set_property BITSTREAM.CONFIG.USR_ACCESS TIMESTAMP [current_design]

set_property BITSTREAM.CONFIG.UNUSEDPIN PULLNONE [current_design]

Design specific constrain

set_property PACKAGE_PIN K2 [get_ports {fclk[0]}]
set_property IOSTANDARD LVCMOS18 [get_ports {fclk[0]}]
set_property CLOCK_DEDICATED_ROUTE FALSE [get_nets fclk_IBUF[0]]

# for fmeter only
# set_false_path -from [get_clocks clk_fpga_0] -to [get_clocks {zsys_i/util_ds_buf_0/U0/IBUF_OUT[0]}]
# set_false_path -from [get_clocks {zsys_i/util_ds_buf_0/U0/IBUF_OUT[0]}] -to [get_clocks clk_fpga_0]
# set_false_path -from [get_clocks clk_fpga_0] -to [get_clocks {zsys_i/util_ds_buf_1/U0/BUFG_O[0]}]

Software Design - Vitis

For Vitis project creation, follow instructions from:

Vitis

Application

zynq_fsbl

TE modified 2020.2 FSBL

General:

• Modified Files: main.c, fsbl_hooks.h/.c (search for 'TE Mod' on source code)

• Add Files: te_fsbl_hooks.h/.c (for hooks and board)

• General Changes: 
  
  • Display FSBL Banner and Device ID

Module Specific:

• Add Files: all TE Files start with te_*
  
  • SI5338 Configuration

zynq_fsbl_flash

TE modified 2020.2 FSBL

General:

• Modified Files: main.c
• General Changes:
  
  • Display FSBL Banner
  • Set FSBL Boot Mode to JTAG
  • Disable Memory initialisation

hello_te0715

Hello TE0715 is a Xilinx Hello World example as endless loop instead of one console output.

u-boot

U-Boot.elf is generated with PetaLinux. Vitis is used to generate Boot.bin.

Software Design -  PetaLinux

For PetaLinux installation and project creation, follow instructions from:

• PetaLinux KICKstart

Config

Start with petalinux-config or petalinux-config --get-hw-description

Changes:

• CONFIG_SUBSYSTEM_ETHERNET_PS7_ETHERNET_0_MAC=""

U-Boot

Start with petalinux-config -c u-boot

Changes:

• CONFIG_ENV_IS_NOWHERE=y
• # CONFIG_ENV_IS_IN_SPI_FLASH is not set
• CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET=0xFA
• CONFIG_SYS_I2C_EEPROM_ADDR=0x50

Change platform-top.h:

Device Tree

/include/ "system-conf.dtsi"
/ {
  chosen {
    xlnx,eeprom = &eeprom;
  };
};

/* default */

/* QSPI PHY */
&qspi {
    #address-cells = <1>;
    #size-cells = <0>;
    status = "okay";
    flash0: flash@0 {
        compatible = "jedec,spi-nor";
        reg = <0x0>;
        #address-cells = <1>;
        #size-cells = <1>;
    };
};



/* ETH PHY */
&gem0 {

	status = "okay";
    	ethernet_phy0: ethernet-phy@0 {
		compatible = "marvell,88e1510";
		device_type = "ethernet-phy";
                reg = <0>;
	};
};


/* USB PHY */
/{
    usb_phy0: usb_phy@0 {
        compatible = "ulpi-phy";
        //compatible = "usb-nop-xceiv";
        #phy-cells = <0>;
        reg = <0xe0002000 0x1000>;
        view-port = <0x0170>;
        drv-vbus;
    };
};

&usb0 {
    dr_mode = "host";
    //dr_mode = "peripheral";
    usb-phy = <&usb_phy0>;
};

/* I2C */
// i2c PLL: 0x70, i2c eeprom: 0x50

&i2c1 {
    rtc@6F {        // Real Time Clock
       compatible = "isl12022";
       reg = <0x6F>;
   };
  //MAC EEPROM
  eeprom: eeprom@50 {
    compatible = "atmel,24c08";
    reg = <0x50>;
  };
};

FSBL patch

Must be add manually --> work in progress

Kernel

Start with petalinux-config -c kernel

Changes:

• CONFIG_RTC_DRV_ISL12022=y

Rootfs

Start with petalinux-config -c rootfs

Changes:

• CONFIG_i2c-tools=y
• CONFIG_busybox-httpd=y (for web server app)
• CONFIG_usbutils=y

Applications

See "<project folder>\os\petalinux\project-spec\meta-user\recipes-apps\"

startup

Script App to load init.sh from SD Card if available.

webfwu

Webserver application suitable for Zynq access. Need busybox-httpd

Additional Software

No additional software is needed.

SI5338

File location "<project folder>\misc\Si5338\Si5338-*.slabtimeproj"

General documentation how you work with this project will be available on Si5338

Appx. A: Change History and Legal Notices

Document Change History

To get content of older revision  got to "Change History" of this page and select older document revision number.

v.13

Legal Notices