Download PDF version of this document.

Table of Contents

Overview

The Trenz Electronic TEBA0714 is a carrier for Trenz Electronic module TE0714 which is an industrial grade module integrated with Xilinx Artix 7. 

Refer to http://trenz.org/teba0714-info for the current online version of this manual and other available documentation.

Key Features

  • Module:
    • TE0714
  • On Board:
    • 2 x User LEDs (Red, Green)
    • 1 x DONE LED (Red)
  • Interface:
    • 2 x Pin Header 50 Pol. (FPGA Bank I/Os and Power)
    • 2x Samtec 100 Pin LSHM Series Connectors
    • 1 x XMOD JTAG/UART Adapter (TE0790)
    • 1 x Pin Header 16 Pol. (JTAG, MGT-CLK, Boot Mode, XADC, I/O's)
    • 1 x Pin Header 10 Pol. (FPGA Bank I/Os and Power)
    • 1 x SFP+ Connectors
  • Power:
    • 1 x LDO Regulator
    • 3.3V  Nominal Power supply
  • Dimension: 
    • 46 mm × 75 mm

Block Diagram


TEBA0714 block diagram

Main Components


TEBA0714 main components
  1. SMT pin header, J26
  2. SMT pin header, J27
  3. Board to Board  (B2B) Connector, JM1
  4. Board to Board  (B2B) Connectorr, JM2
  5. XMOD header, JX1
  6. Voltage Regulator, U1
  7. User Red LED, D2
  8. User Green LED, D1 (Red)
  9. SFP+ Connector, J1
  10. User Red LED, D3
  11. 50 pin header (Not assembled),  J20
  12. 16 pin header (Not assembled),  J3,
  13. 10-pin header (Not assembled), J4 
  14. 50-pin header (Not assembled), J17

Initial Delivery State


Storage device nameContentNotes
---------
Initial delivery state of programmable devices on the module

Configuration Signals


SignalMODE Signal StateBoot ModeNote
BOOTMODE0Slave SelectMAP
1Master SPI
Boot process.


SignalB2BSignal StateNote
PROG_BJM1-94Active LowClear FPGA configuration  and initiate a new configuration
Reset process.

Signals, Interfaces and Pins

Board to Board (B2B) I/Os

Number of I/O signals and Interfaces connected to the B2B connector:

B2B ConnectorInterfaceNumber of I/ONotes
JM1



User I/O52 Single ended, 27 Differential-
MGT lanes4 Differential, 2 lanes
MGT reference clock input2 Single ended, 1 Differential
JTAG4 Single ended
SoM control signals2 Single endedPROG_B, DONE
JM2User I/O36 Single ended or 18 differential-
SFP+ Interface control signals8 Single ended
QSPI interface6 Single ended
UART interface2 Single ended
User LEDs2 Single endedRed, Green
SoM control signals1 Single endedBOOTMODE
General PL I/O to B2B connectors information

On-board Pin Header

TEBA0714 is equipped with four pin headers J17, J20, J3 and J4 which are not assembled on the board, in case of need customer can solder the pins and have access to the signals in the following table.

Pin HeaderInterfaceNumber of I/ONotes
J17



User I/O36 Single ended, 18 DifferentialModule FPGA Bank 14
SPI interface6 Single ended-
Power4 Single ended3.3V, V_CFG
J20User I/O42 Single ended or 21 differentialModule FPGA Bank 34
Power4 Single ended3.3V, V_CFG
User LEDs2 Single endedRed, Green
SoM control signals1 Single ended'BOOTMODE'
J3JTAG 4 Single ended
UART2 Single endedB14_L25, B14_L0
ADC2 Single ended
Clock2 Single ended, 1 Differential
Power4 Single ended3.3V, V_CFG
Control Signals2 Single endedBOOTMODE, PROG_B
J4User I/O6 Single ended or 3 differential
Power2 Single ended3.3V, 3.3V_OUT
General I/O to Pin headers information

JTAG Interface Base

JTAG access to the mounted SoM is provided through B2B connector JM1 and JM2 and is also routed to the XMOD JTAG/UART header JX1.

XMOD Header PinSchematicB2B ConnectorPin HeaderNote
AB14_L25JM2-97J3-4UART Transfer
BB14_L0JM2-99J3-7UART Receive
EBOOTMODEJM2-100J3-9
GPROG_BJM1-94J3-11
CTCKJM1-90J3-4
DTDIJM1-86J3-10
FTDOJM1-88J3-8
HTMSJM1-92J3-12
3.3V3.3VJM1-97,99J3,J4,J17,J20Nominal Input Voltage
VIOV_CFG-J17-45Configuration Voltage
JTAG pins connection

The DIP-switch S2 on XMOD Adapter TE0790 must be set as the following table.

S2StatusDescriptionNotes      
1ONUpdate Mode JTAG access to SC CPLD only
2OFFMust be in OFF state always
3OFF3.3V  is inputsupplied from pin headers externally
4OFFVIO is inputsupplied from pin header externally
JTAG pins connection

SFP+ Connector

PinConnected toNotes
VCCR3.3V
VCCT3.3V
VREFGND
TD+/TD-MGT TXMGT Lane
RD+/RD-MGT RXMGT Lane
TX/FAULTSFP0_TX_FAULSFP_CTRL
TX/DISABLESFP0_TX_DISSFP_CTRL
MOD-DEF2SFP0_SDASFP_CTRL
MOD-DEF1SFP0_SCLSFP_CTRL
MOD-DEF0SFP0_MT_DEF0SFP_CTRL
RS0/RS1SFP0_RS0_1SFP_CTRL
LOSSFP0_LOSSFP_CTRL
SFP+ Connector Information

SMT Pin Headers

There are two SMT Pin Headers, J26-J27.
J26 is available to choose voltage level for VCCIO34 (FPGA Bank 34) and J27 is provided to set the voltage level of V_CFG (Configuration Voltage). In order to set the voltage level, you should connect it to the corresponding pin with the target value voltage.

SMT Pin HeaderVCCIO/VCCVoltage LevelNotes
J26VCCIO34

1.8V
2.5V
3.3V3.3V_OUT
J27V_CFG

1.8V
2.5VV_CFG0
3.3V3.3V_OUT
SMD Connector Information

On-board Peripherals



Chip/InterfaceDesignatorNotes
LEDsD1...3
On board peripherals

LEDs

DesignatorColorConnected toActive LevelNote
D1GreenGLEDActive High
D2RedRLEDActive High
D3RedDONEActive LowDONE pin
On-board LEDs

Power and Power-On Sequence

Power Supply

Power supply with minimum current capability of 3A for system startup is recommended.

The on-board voltages of the carrier board will be powered up with an external power-supply with nominal voltage of 3.3V.

Power Consumption

Power Input PinTypical Current
3.3V* TBD
Power Consumption

* TBD - To Be Determined

Power Distribution Dependencies

3.3V can be supplied through Pin Headers on specific pins. 

Power Distribution

Power-On Sequence

There is no specific power-on sequence. After power on, the module and carrier will be powered on.

Power Sequency

Power Rails

Power Rail Name

B2B , JM1 Pin

B2B JM2 Pin

Pin Header J17Pin Header J20Pin Header J3Pin Header J4DirectionNotes
3.3V99,97-5, 465, 4655Input
1.8V-18----InputComes from Module
3.3V_OUT8354---6Output
VCCIO3461--45--OutputVariable voltage level
V_CFG53-----InputVariable voltage level
Module power rails.

Board to Board Connectors

TEBA0714 carrier use two  Samtec Razor Beam LSHM Connectors on the bottom side.

These connectors are hermaphroditic. Odd pin numbers on the module are connected to even pin numbers on the baseboard and vice versa.

4 x 5 modules use two or three Samtec Razor Beam LSHM connectors on the bottom side.

  • 2 x REF-189016-02 (compatible to LSHM-150-04.0-L-DV-A-S-K-TR), (100 pins, "50" per row)
  • 1 x REF-189017-02 (compatible to LSHM-130-04.0-L-DV-A-S-K-TR), (60 pins, "30" per row) (depending on module)
Connector Mating height

When using the same type on baseboard, the mating height is 8mm. Other mating heights are possible by using connectors with a different height

Order numberConnector on baseboardcompatible toMating height
23836REF-189016-01LSHM-150-02.5-L-DV-A-S-K-TR6.5 mm

LSHM-150-03.0-L-DV-A-S-K-TRLSHM-150-03.0-L-DV-A-S-K-TR7.0 mm
23838REF-189016-02LSHM-150-04.0-L-DV-A-S-K-TR8.0 mm

LSHM-150-06.0-L-DV-A-S-K-TRLSHM-150-06.0-L-DV-A-S-K-TR10.0mm
26125REF-189017-01LSHM-130-02.5-L-DV-A-S-K-TR6.5 mm

LSHM-130-03.0-L-DV-A-S-K-TRLSHM-130-03.0-L-DV-A-S-K-TR7.0 mm
24903 REF-189017-02LSHM-130-04.0-L-DV-A-S-K-TR8.0 mm

LSHM-130-06.0-L-DV-A-S-K-TRLSHM-130-06.0-L-DV-A-S-K-TR10.0mm
Connectors.

The module can be manufactured using other connectors upon request.

Connector Speed Ratings

The LSHM connector speed rating depends on the stacking height; please see the following table:

Stacking heightSpeed rating
12 mm, Single-Ended7.5 GHz / 15 Gbps
12 mm, Differential

6.5 GHz / 13 Gbps

5 mm, Single-Ended11.5 GHz / 23 Gbps
5 mm, Differential7.0 GHz / 14 Gbps
Speed rating.
Current Rating

Current rating of  Samtec Razor Beam™ LSHM B2B connectors is 2.0A per pin (2 adjacent pins powered).

Connector Mechanical Ratings
  • Shock: 100G, 6 ms Sine
  • Vibration: 7.5G random, 2 hours per axis, 3 axes total


Manufacturer Documentation

  File Modified
PDF File hsc-report_lshm-lshm-05mm_web.pdf High speed test report 07 04, 2016 by Thorsten Trenz
PDF File lshm_dv.pdf LSHM catalog page 07 04, 2016 by Thorsten Trenz
PDF File LSHM-1XX-XX.X-X-DV-A-X-X-TR-FOOTPRINT(1).pdf Recommended layout and stencil drawing 07 04, 2016 by Thorsten Trenz
PDF File LSHM-1XX-XX.X-XX-DV-A-X-X-TR-MKT.pdf Technical drawing 07 04, 2016 by Thorsten Trenz
PDF File REF-189016-01.pdf Technical Drawing 07 04, 2016 by Thorsten Trenz
PDF File REF-189016-02.pdf Technical Drawing 07 04, 2016 by Thorsten Trenz
PDF File REF-189017-01.pdf Technical Drawing 07 04, 2016 by Thorsten Trenz
PDF File REF-189017-02.pdf Technical Drawing 07 04, 2016 by Thorsten Trenz
PDF File TC0923--2523_report_Rev_2_qua.pdf Design qualification test report 07 04, 2016 by Thorsten Trenz
PDF File tc0929--2611_qua(1).pdf Shock and vibration report 07 04, 2016 by Thorsten Trenz



Technical Specifications

Absolute Maximum Ratings

SymbolsDescriptionMinMaxUnit
VINInput Supply Voltage-0.36V
T_STRStorage Temperature-40125°C
PS absolute maximum ratings

Recommended Operating Conditions

Operating temperature range depends also on customer design and cooling solution. Please contact us for options.

ParameterMinMaxUnitsReference Document
VIN3.1353.465V3.3V Nominal Power Supply
T_OPR-4085°C
Recommended operating conditions.

Physical Dimensions

  • Module size: 46 mm × 75 mm.  Please download the assembly diagram for exact numbers.
  • Mating height with standard connectors: 8 mm.

PCB thickness: 1.64 mm.


Physical Dimension

Currently Offered Variants 


Trenz shop TEBA0714 overview page
English pageGerman page
Trenz Electronic Shop Overview

Revision History

Hardware Revision History


DateRevisionChangesDocumentation Link
2016-06-1501
  • Initial Release
REV01
Hardware Revision History

Hardware revision number can be found on the PCB board together with the module model number separated by the dash.

Board hardware revision number.

Document Change History


DateRevisionContributorDescription

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • Initial Release
--all

Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]

  • --
Document change history.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.


Error rendering macro 'page-info'

Ambiguous method overloading for method jdk.proxy241.$Proxy3496#hasContentLevelPermission. Cannot resolve which method to invoke for [null, class java.lang.String, class com.atlassian.confluence.pages.Page] due to overlapping prototypes between: [interface com.atlassian.confluence.user.ConfluenceUser, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject] [interface com.atlassian.user.User, class java.lang.String, class com.atlassian.confluence.core.ContentEntityObject]


  • No labels