Download a PDF version of this document.


Overview

The TEB0955 is a carrier which makes the SoM MGTs accessible by M.2 and zQSFP+ devices, IOs accessible by 2x CRUVI HS and 1x CRUVI LS connector. Furthermore, it provides a gigabit Ethernet and a USB2.0 socket. For debugging and programming a USB to JTAG and UART converter is on-board. The carrier offers a 12 V PWM Fan header for cooling and multiple DIP switches, buttons and LEDs. To facilitate an easy installation into an enclosure, pin headers for all DIP switches and buttons as well as the LEDs can optional be placed onto the carrier.

Refer to https://trenz.org/teb0955-info for current online available documentation.

Key Features

  • Supported SoM
  • On Board
    • Channel Configuration logic for USB Type C
      • Optional 2): Level shifter for dynamic USB OTG configuration
    • Programmer via USB 2.0 to JTAG/UART/Reset bridge
    • Programmer configuration EEPROM
    • CAN transceiver with silent mode and fault flag
    • LEDs:
      • 4x status - Power, UART and SoM Error/Done
      • 2x user - SoM PS and PL
    • Clock sources:
      • Programmable MGT Clock
      • Clock for PCIe up to PCIe 4.0
      • PCIe common clock - M.2 and SoM
      • Optional 2):
        • Additional Programmable MGT Clock
        • Fixed MGT Clock
  • Interface
    • Trenz 4 x 5.64 SoM 2x B2B connector (Samtec ADF6 240 pins) socket
    • zQSFP+ connector 4x MGT (RX/TX)
    • M.2 M-Key 4x MGT (RX/TX)
    • RJ45 GBit Ethernet with status LEDs
    • 2x CRUVI HS with combined - 48x SE / 24x DIFF / 4x4 MIPI lanes
    • CRUVI LS - 4x SE
    • MicroSD socket (SD 3.0)
    • USB Type C for USB 2.0
    • USB Type C for USB 2.0 to JTAG and UART converter
    • CAN with selectable termination
    • 4x Boot Mode DIP switches
    • Button for system reset
    • Optional 1) : Button for only CPU reset
    • Optional 1) : Pin headers to facilitate an easy case installation for:
      2x I2C and Interrupts, UART, LEDs, DIP switches, Reset Buttons and MIO GPIOs
  • Power
    • 12 V Single Rail power supply
    • Supply protection - Over and under voltage, Reverse polarity and fuse (4 A)
    • Battery holder (CR1220) for backup supply
    • Pin header for 12 V PWM fan
  • Dimension
    • 105 mm x 150 mm
  • Notes
    1) AM0010 supports not all features, see 4 x 5.64 Carriers.
    2) Available as assembly variant or upon request.

Block Diagram

Legend :

* : MIPI usage SoM/SoC dependent

Optional devices / pin header.

TEB0955 block diagram

Main Components

 

TEB0955 main components
  1. Barrel socket (2.1 mm) - Power Input, J27
  2. Fan Header - 12 V PWM, J29
  3. Battery Holder - CR1220, B1
  4. B2B Connector - ADF6 240 pin, JB5, JB6
  5. Optional: Pin Header 2.54 mm, 3x Reset - J21, J22, J23
  6. zQSFP+ Connector, U1
  7. M.2 Connector, U5
  8. CRUVI HS Connectors, J1, J2
  9. CRUVI LS Connector, J3
  10. RJ45 Gbit Ethernet, J11
  11. USB Type C - USB 2.0, J9 
  12. USB Type C - Programmer / USB 2.0 to JTAG/UART/Reset bridge, J13
  13. MicroSD Socket, J10
  14. LEDs - Status Power/SoM, D1, D2
  15. LEDs - User definable, D3, D4
  16. LEDs - Status USB VBUS/SoM, D5, D6
  17. LEDs - Status UART0/M.2, D7, D8
  18. Optional: Pin Header 2.54mm - LED/IO, J20
  19. Buttons Reset System, S1, S5
  20. Optional Button - Reset CPU, S2
  21. 4x DIP Switches - Boot mode configuration, S3
  22. 2x DIP Switches - Boot mode configuration, S4
  23. Box Header 2.54 mm - CAN, J28
  24. Pin Header 2.54 mm - CAN termination configuration, J26
  25. Pin Header 2.54 mm - USB OTG configuration, J5
  26. Optional: Pin Header 2.54 mm - JTAG, J12
  27. Optional: Pin Header 2.54 mm - UART0, J25
  28. Optional: Pin Header 2.54 mm - UART1, J14
  29. Optional: Pin Header 2.54 mm, U_I2C - J17, M/U_INT - J16, M_I2C - J15
  30. Optional: Pin Header 2.54 mm - Boot mode configuration, J18
  31. Optional: Pin Header 2.54 mm, PWR_EX - J19, PWR_EN - J24

Initial Delivery State

Storage device name

Designator

Content

Notes

EEPROM

U19

Programmer configuration.

Do not overwrite!

Initial delivery state of programmable devices

Signals, Interfaces and Pins

Connectors

Connector Type

Designator

Interface

IO count

Notes

B2B

JB5

MGT M.2

4x MGT (RX/TX)


M.2

U5

MGT M.2

4x MGT (RX/TX)


B2B

JB5

MGT zQSFP+

4x MGT (RX/TX)


zQSFP+

U1

MGT zQSFP+

4x MGT (RX/TX)


B2B

JB5

IO CRUVI HS

24x SE / 12x DIFF / 2x4 MIPI


CRUVI HS

J1

IO CRUVI HS

24x SE / 12x DIFF / 2x4 MIPI


B2B

JB5

IO CRUVI HS

24x SE / 12x DIFF / 2x4 MIPI


CRUVI HS

J2

IO CRUVI HS

24x SE / 12x DIFF / 2x4 MIPI


B2B

JB6

IO CRUVI LS

4x SE


CRUVI HS

J3

IO CRUVI LS

4x SE


B2B

JB6

USB OTG

1x DIFF


USB Type C

J5

USB OTG

1x DIFF


B2B

JB6

USB 2.0

1x DIFF


USB Type C

J13

USB 2.0

1x DIFF


B2B

JB5

ETH MDI

4x DIFF


RJ45

J11

ETH MDI

4x DIFF


B2B

JB5

UART / CAN

2x SE / 1x DIFF


B2B

J14 / J26 / J28

UART / CAN

2x SE / 1x DIFF


Pin Header 2.54 mm

J20

IO

3x SE


B2B

JB5

SDIO

7x SE


MicroSD socket

J20

SDIO

7x SE


Board connectors

Test Points

Test

Point

REV02


Notes

Top

Bottom

Signal

TP1

x


V_USB0


TP2


x

V_SD_IO


TP3

x


V_SD_IO


TP4

x


M_SCL_LS


TP5

x


M_SDA_LS


TP6

x


M_INT_R#


TP7




Not used

TP8




Not used

TP9




Not used

TP10


x

V_MOD1


TP11

x


FAULTn_12V


TP12

x


V_MOD1


TP13

x


V_BAT


TP14


x

V_BAT


TP15

x


GND


TP16


x

GND


TP17

x


PG_5V0


TP18

x


PG_3V3


TP19


x

3V3


TP20


x

5V0


TP21

x


3V3


TP22

x


5V0


TP23


x

3V3_AO


TP24

x


PG_C_VADJ


TP25

x


1V8


TP26


x

V_IO_CFG


TP27

x


3V3_AO


TP28


x

1V8


TP29


x

C_VADJ


TP30

x


V_IO_CFG


TP31

x


C_VADJ


TP32


x

V_USB0


Test points information

On-board Peripherals

Chip / Interface

Designator

Connected to

Notes

Channel Configuration logic for USB Type C

U11

  • Pin Header for configuration J5
  • USB Type C J9
  • B2B JB6
  • I2C 1) (via optional level shifter U14)


I2C IO expander

U2

  • zQSFP+ Connector U1
  • M_I2C 1)
  • Oscillator U12
  • Oscillator U32


I2C IO expander

U8

  • M.2 Connector U5
  • M_I2C 1)
  • PCIe common CLK U31
  • Oscillator U33


Programmer USB 2.0 to JTAG/UART bridge

U15

  • EEPROM U19
  • Oscillator U20
  • USB Type C J13
  • Buttons S2, S5
  • Pin Header J21, J22, J23
  • JTAG and UART Header J12, J25
  • LED UART status D7
  • B2B JB6


PCIe common CLK

U31

  • SoM via B2B JB5
  • M2 Connector U5

100 MHz, enable via U8 I2C IO expander.

Programmable Oscillator

U32

  • B2B JB5

Default 156¼ MHz, enable via U2 I2C 1) IO expander.

Oscillator

U20

  • JTAG/UART/IO Bridge U15

12 MHz

Optional: Programmable Oscillator

U33

  • B2B JB5

Default 156¼ MHz, enable via U8 I2C 1) IO expander.

Optional: Oscillator

U12

  • B2B JB5

125 MHz, enable via U2 I2C 1) IO expander.

On-board peripherals

1) List of I2C bus names and devices including addresses is available in board schematic.


Configuration and System Control Signals

Control Signals and Buses

Signal Name

Connector.Pin

Direction 1)

Description

RST_SYS#

JB6.C58 / J23.1

OUT / IN

SoM Reset Signal.

RST_CPU#

JB6.C59 / J22.1

OUT / IN

SoM CPU Reset Signal.

RST_M2C#

JB6.B58 / J21.1

IN / OUT

SoM to carrier periphery Reset Signal.

PWR_EN_IO

JB6.D59

IN

SoM enables power rail 5V0, C_VADJ, 3V3 and V_IO_CFG.

PWR_EN

JB6.D58

OUT

Signal to SoM begin of power sequencing.

MODE0 / MODE1 / MODE2 / MODE3

JB6.C54 / JB6.C55 / JB6.C56 / JB6.C57

OUT

SoM boot mode selection. Signals present on 4x DIP switch S3, 2x DIP switch S4 and pin header J18.

SD_CD#

JB6.A57

OUT

MicroSD card detect signal.

SD_D4

JB6.A53

IN

Select the microSD socket voltage.

Low = 3.3 V, High = 1.8 V.

USB0_ID

JB6.B47

OUT

USB0 OTG mode signal.

USB0_CPEN

JB6.C48

IN

Enable USB0 VBUS voltage.

V_BUS_R

JB6.D46

OUT

USB VBUS signal.

PERST0# / PERST1# / (M2PERSTn)

JB6.B51 / JB6.B52

IN

M.2 PCIe reset signal.

PERST0# is usually from SoC PS, PERST1# from SoC PL, resistors  R29, R30 should be set according to SoM.

M2_PEDET / M2_SLEEP / M2_CLKRQ / M2_WAKEn

U5.69 / U5.38 / U5.52 / U5.54

Signal dependent

M.2 PCIe control signals. Accessible via M_I2C/IO expander U8.

QSFP_MODSEL / QSFP_MODPRS / QSFP_RESET / QSFP_INT# / QSFP_LPMODE

U1.8 / U1.27 / U1.9 / U1.28 / U1.31

Signal dependent

zQSFP+ control signals. Accessible via U_I2C/IO expander U2.

GPIO1

JB6.C48 / J28.4

IN

Control fan speed via PWM.

GPIO3

JB6.C50 / J28.3

OUT

Fan tacho signal.

JTAG ( C_HS_Y_JTDI / C_HS_Y_JTDO / C_HS_Y_JTMS / C_HS_Y_JTCK )

JB6.D36 / JB6.D37 / JB6.D38 / JB6.C37

J2.51 / J2.53 / J2.55 / J2.59

Signal dependent

CRUVI JTAG interface, alternative usable as 3.3V IOs

C_HS_Y_JTAGEN

JB6.D39 / J2.59

IN / OUT

CRUVI JTAG enable, alternative usable as 3.3V IO.

JTAG ( TDI / TCK / TDO / TMS )

JB6.D51 / JB6.D52 / JB6.D54 / JB6.D55

J12.2 / J12.4 / J12.3 / J12.1

Signal dependent

SoM JTAG

UART ( UART0_RX / UART0_TX )

JB6.B49 / JB6.B50

J25.2 / J25.3

Signal dependent


UART ( UART1_RX / UART1_TX )

CAN ( CAN_RX / CAN_TX )

JB6.A49 / JB6.A50
J14.2 / J14.3


Signal dependent

Intended to be used as either UART or CAN.

JB6.A49 / JB6.A50

CAN ( CAN_P/CAN_H / CAN_N/CAN_L )

J28.4/J26.4 / J28.3/J26.3

Signal dependent

CAN termination selection

SD_D7 / CAN_S

JB6.A56

IN

CAN transceiver mode signal.

CAN_FAULT

JB6.A55

OUT

CAN fault output

I2C ( M_SCL / M_SDA )

JB6.C50 / JB6.C51
J15.3 / J15.1

Signal dependent


M_INT#

JB6.C49 / J16.1

OUT / IN

M I2C interrupt signal.

I2C ( U_SCL / U_SDA )

JB6.D33 / JB6.D34
J17.3 / J17.1

Signal dependent


U_INT#

JB6.D35 / J16.3

OUT / IN

U I2C interrupt signal.

I2C ( C_HS_X_SMB_SCL / C_HS_X_SMB_SDA )

JB6.A37 / JB6.B37
J1.7 / J3.5

Signal dependent

Alternative 3.3V SoC PL IO.

C_HS_X_SMB_ALERT

JB6.A38 / J3.3

OUT / IN

X SMB I2C interrupt signal.

Alternative 3.3V SoC PL IO.

I2C ( C_HS_Y_SMB_SCL / C_HS_Y_SMB_SDA )

JB6.B39 / JB6.B38
J1.7 / J3.5

Signal dependent

Alternative 3.3V SoC PL IO.

C_HS_Y_SMB_ALERT

JB6.C35 / J3.3

OUT / IN

Y SMB I2C interrupt signal.

Alternative 3.3V SoC PL IO.

I2C ( C_LS_C_SCL / C_LS_C_SDA )

JB6.A35 / JB6.A32
J3.2 / J3.1

Signal dependent


ERROR_R / DONE

JB6.A39 / JB6.C53

IN

Signals drive the LEDs D2 and D6

ETH0_LED0# / ETH0_LED1#

JB6.A42 / JB6.B43

IN

LEDs RJ45 J11

PL_LED

JB6.C38

IN

User definable LED from SoC PL/FPGA side.

1) Direction:

    • IN: Input from the point of view of this board.

    • OUT: Output from the point of view of this board.

    • INOUT: Bidirectional signal.
    • Signal dependent: A Signal can have different functions and directions as part of a Bus.
Control signals and buses

Jumpers

Jumper

header

Net name / Connector.pin


Notes

Output

Input

J5

-

-

Jumpers for USB mode selection: Host, Device or OTG (default).

Refer to the schematic for jumper placements.

Jumpers

Buttons


Button


Signal

Voltage level


Function


Notes

Low

high

S1 / S5

RST_SYS#

pressed

unpressed

Reset signal for SoM.

S1 intended for desktop use, S5 intended for use in enclosure.

S2

RST_CPU#

pressed

unpressed

Reset signal to SoM.

Button is optional.

J21

RST_M2C#

pressed

unpressed

Reset signal to SoM.

Button not on-board. Only solder pads, optional as pin header.

Buttons

DIP switches

DIP switch groups

DIP switch

Signal name / Connector.pin

Description

S3

S3A

MODE0 / JB6.C54

Sets the SoMs boot mode.

S3 for desktop use, S4 for enclosure, reduced select ability of boot-modes when using S4 can also be modified via jumpers on J18.

Refer to the schematic for further information.

S3

S3B

MODE1 / JB6.C55

S3 / S4

S3C / S4B

MODE2 / JB6.C56

S3 / S4

S3D / S4A

MODE3 / JB6.C57

DIP switches

Power and Power-On Sequence

Power Rails

Power Rail Name / Schematic Name

Description

Connector.Pin

Direction 1)

Notes

12V_IN

Carrier supply 12.0 V

J27.1

IN


1V8

Auxiliary logic supply from SoM.

JB5.C7 / JB5.C15 / JB6.B7 / JB6.B15

IN


3V3_AO

From SoM to power optional features.

JB6.B59

IN


V_MOD1

Main supply for SoM and PWM Fan.

JB5.A7 / JB5.A15 / JB5.A47 / JB5.A55 /
JB5.B5 / JB5.B11 / JB5.B17 / JB5.B45 / JB5.B51 / JB5.B57
JB6.C5 / JB6.C11 / JB6.C17 / JB6.D7 / JB6.D15

J29.2

OUT


5V0

Supply for CRUVI HS, LS and CAN header.

J1.60 / J2.60 / J3.12 / J26.5

OUT


3V3

Supply for CRUVI HS and LS and other periphery.

JB6.B25

J1.4 / J1.9

J2.4 / J2.9

J3.10

OUT


1V8

Reference voltage from SoM.

J25.4

J14.4

OUT


V_BAT

Backup supply for SoM.

JB6.A59

OUT


C_VADJ

Auxiliary supply for SoM and CRUVI HS.

JB5.D3 / JB5.D17

J1.36 / J2.36

OUT


V_IO_CFG

Auxiliary supply for SoM. Reference voltage for JTAG header J12.

JB6.C52

J12.6

OUT


1) Direction:

    • IN: Input from the point of view of this board.
    • OUT: Output from the point of view of this board.
Power rails

Recommended Power up Sequencing

Sequence

Net name

Recommended Voltage Range

Pull-up/down

Description

Notes

0

-

-

-

Configuration SoM signal setup.

See Configuration and System Control Signals.

This enables automatically SoM by setting PWR_EN high.

1

12V_IN

11.6 V to 12.6 V

-

Apply main SoM supply.


2

PWR_EN_IO

-

-

SoM enables TEB0955 IO rails via PWR_EN_IO when it is ready. 



SD_D4

-

-

Is a software driven signal for selecting SD_IO voltage, usually should be low (for selecting 3.3V for SD2.0 mode), and can be driven high after initialisation to switch to SD3.0 mode (selecting 1.8V). 


Power sequencing

Board to Board Connectors

The 4 x 5.64 modules use Samtec AcceleRate HD High-Density on bottom side.
  • 2x ADM6-60-01.5-L-4-2 (legacy) or ADM6-60-01.5-L-4-0 (240 pins, 60 per row)
    •  Mates with ADF6-60-03.5-L-4-2 (legacy) or ADF6-60-03.5-L-4-0

The carriers use Samtec AcceleRate HD High-Density on top side.

  • 2x ADF6-60-03.5-L-4-2 (legacy) or ADF6-60-03.5-L-4-0 (240 pins, 60 per row)
    • Mates with ADM6-60-01.5-L-4-0 (legacy) or ADM6-60-01.5-L-4-2
Features
  • Board-to-Board connector 240-pins / 60 contacts per row
  • Pitch:           0.025" (0.635 mm)
  • Data Rate:
    • ADM6-XX-XX.X-X-X-2: 56 Gbps
    • ADM6-XX-XX.X-X-X-0: 64 Gbps
  • Mates with: ADM6/APF6
  • Insulator Material: Black LCP
  • Contact Material:  Copper Alloy
  • Plating:                 Au or Sn over 50 µ" (1.27 µm) N
  • Operating Temperature Range: -55 ºC to +125 ºC
  • Lead-Free solderable: Yes
  • RoHS Compliant:        Yes
Connector Mating height

When using the same type on baseboard, the mating height is 5 mm. Other mating heights are possible by using connectors with a different height:

Order numberREF numberSamtec NumberTypeContribution to stacking heightComment
30095REF-30095ADM6-60-01.5-L-4-2Module connector1.5 mmStandard connector used on modules (legacy)
- -ADM6-60-01.5-L-4-0Module connector1.5 mmAlternative connector
31137REF-31137ADF6-60-03.5-L-4-2Baseboard connector3.5 mmStandard connector used on carrier (legacy)
--ADF6-60-03.5-L-4-0Baseboard connector3.5 mmAlternative connector
Connectors.

The module can be manufactured using other connectors upon request.

Connector Speed Ratings

The AcceleRate HD High-Density connector speed rating depends on the stacking height; please see the following table:

ConnectorStacking heightSpeed rating
ADM6-XX-XX.X-X-X-25 mm56 Gbps
ADM6-XX-XX.X-X-X-05 mm64 Gbps
Speed rating.
Current Rating

Current rating of Samtec AcceleRate HD High-Density B2B connectors is 1.34 A per pin (4 pins powered).

Connector Mechanical Ratings
  • Shock:      100G, 6 ms Sine
  • Vibration:  7.5G random, 2 hours per axis, 3 axes total


Manufacturer Documentation



Technical Specifications

Absolute Maximum Ratings *)

Warning!

The listed values ONLY reflect this board. Connected SoMs / Boards are not considered. 

Power Rail Name / Schematic Name

Description

Min

Max

Unit

Notes

12V_IN

Carrier supply 12.0 V

-25.0

25.0

V


1V8

Auxiliary logic supply from SoM.

-0.3

3.63

V


3V3_AO

From SoM to power optional features.

-0.3

6.3

V


Absolute maximum ratings

*) Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under "Recommended Operating Condition". Exposure to absolute-maximum rated conditions for extended periods may affect device reliability.

Recommended Operating Conditions

Temperature range

There are three exceptions preventing the board of being classified as completely compatible with industrial ambient temperature range of -40 °C to 85 °C:

  • SD Card socket J10 which has lower limit of -30°C,
  • Push button S4 which has lower limit of -20°C,
  • Push button S5 which has lower limit of-35°C.

All other components of TEB0955 cover at least industrial ambient temperature range of -40 °C to 85 °C. If above mentioned components are not used / not essential for the design they can be ignored. These classification does not take into account the entire custom system consisting of:

  • Customer SoC/FPGA design. The allowed main SoC/FPGA temperature range is specified from the vendor by junction temperature using classes (C, E, I). See vendor documentation.
  • Cooling solution, active and or passive cooling.
  • Climate or environmental conditions besides ambient temperature range.
  • Module orientation, neighbouring assemblies, neither other heat sources nor the SoC as heat source to other components.

The temperature of individual components should not exceed the specified range due to self-heating or heating by adjacent components. The actual operating temperature range will depend on the customer design, usage, environment and cooling solution. Consult Cooling Solutions for more information.

Voltage rails

The following table aims to be generic for all variants. The voltage ranges are consistent across assembly variants, but exceptions are possible (custom request).

Power Rail Name / Schematic Name

Min

Max

Unit

Reference Document

12V_IN

11.4

12.6

V

Schematic

1V8

1.746

1.854

V

Schematic

3V3_AO

3.201

3.399

V

Schematic

Recommended operating conditions

Physical Dimensions

  • Module size: 105 mm x 150 m.  Please download the assembly diagram for exact numbers.

  • Mating height with standard connectors: 5 mm.

  • PCB thickness: 1.466 mm ±10 %.

Physical dimension

Currently Offered Variants 

Trenz shop TEB0955 overview page*
English pageGerman page
Trenz Electronic shop overview

Revision History

Hardware Revision History

The hardware revision number can be found on the PCB board together with the module's model number, separated by a dash.

Board hardware revision number

Date

Revision

Changes

Documentation Link

2026-07

02

  1. Corrected DIR pin connection of Levelshifter U9 and removed patch label.
  2. Removed UART and JTAG test points.
  3. Changed J9 and J13 from micro USB to USB-C. Therefore also added U11, optional I2C Levelshifter U14 and corresponding circuits.
  4. Changed J5 from 8 pin to 10 pin header, to set PORT connection of U11 via jumper.
  5. Changed MP1.. MP6 to 10mm version and removed from schematic, will be added manually to BOM when nedded.
  6. Added zero Ohms R150, R151 and set power switch U29 to default not fitted.
  7. Changed default assembly option for PCIe Reset: R29 fitted, R30 not fitted.
  8. Changed J11 to 74991114411, replaced C43 by 0R R152.
  9. Added C43.
  10. Changed SD 3.0 level shifter pin compatible from NXS0506GUX to NVT4858HKZ.

REV02

2025-06

01

  • Initial Revision

-

Hardware revision history

Document Change History

Date

Revision

Contributor

Description

  • Update to TRM template revision 4.3.9

v.7

 Kilian Jahn

  • Corrected minor errors

2026-01-23

v.6

 Martin Rohrmüller

  • Updated to REV02

v.4

Martin Rohrmüller

  • Corrected Typo in block diagram

v.2

Kilian Jahn

  • Initial TRM in template revision 4.3.2

--

all

  • --

Document change history.

Disclaimer

Data Privacy

Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy

Document Warranty

The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.

Limitation of Liability

In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.

Product Disclaimer

Products (incl. Software and Firmware) are exclusively designed, manufactured, and distributed for industrial applications. They are not intended, authorized, or certified for use in critical safety applications, medical devices, aerospace, nuclear, life-support, traffic-control, military, or other environments where malfunction or failure could result in personal injury, death, or significant property or environmental damage.

Trenz Electronic GmbH (“Manufacturer”) excludes any liability for inappropriate use in such contexts. The Customer bears all responsibility for verifying suitability and compliance with applicable regulations when deploying in any critical-use scenario. The Customer also agrees to indemnify and hold harmless the Manufacturer from any third-party claims or liabilities arising from such use.

Copyright Notice

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.

Technology Licenses

The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.

Environmental Protection

To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.

REACH, RoHS and WEEE

REACH

Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).

RoHS

Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.

WEEE

Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).

Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.

Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.



Table of contents