Download PDF version of this document.
Table of Contents
Overview
The Trenz Electronic TE0841-02 is an industrial-grade 4 x 5 cm SoM integrating Xilinx Kintex UltraScale FPGA, 2 GByte of DDR4 SDRAM, 64 MByte QSPI Flash for configuration and operation and powerful switch-mode power supplies for all on-board voltages. Numerous configurable I/Os are provided via rugged high-speed strips. All this on a tiny footprint, smaller than a credit card size at very competitive price. All Trenz Electronic 4 x 5 cm SoMs are mechanically compatible.
Key Features
- Xilinx Kintex UltraScale FPGA (XCKU035 or XCKU040)
- 2 banks of 1024 MByte DDR4 SDRAM, 32bit wide memory interface
- 512 Mbit (64 MByte) QSPI Flash
- 3 x Samtec Razor Beam LSHM B2B, 260 terminals total
- 60 x HR I/Os
- 84 x HP I/Os
- 8 x GTH transceiver lanes (TX/RX)
- 2 x MGT external clock inputs - Clocking
- Si5338 - 4 output PLLs, GT and PL clocks
- 200 MHz LVDS oscillator - All power supplies on-board, single power source operation
- Evenly spread supply pins for optimized signal integrity
- Size: 40 x 50 mm
- 3 mm mounting holes for skyline heat spreader
- Rugged for industrial applications
Additional assembly options are available for cost or performance optimization upon request.
Block Diagram
Main Components
Photo shows similar TE0841-01
- Xilinx Kintex UltraScale FPGA, U1
- Ultra performance oscillator @25.000000 MHz, U3
- 12A PowerSoC DC-DC converter (0.95V), U14
- 12A PowerSoC DC-DC converter (0.95V), U7
Low-jitter precision LVDS oscillator @200.0000 MHz, U11
- Low-dropout (LDO) linear regulator (MGTAVTT 1.20V), U8
- Low-dropout (LDO) linear regulator (MGTAVCC 1.02V), U12
- Samtec Razor Beam™ LSHM-150 B2B connector, JM1
- Samtec Razor Beam™ LSHM-150 B2B connector, JM2
- Samtec Razor Beam™ LSHM-130 B2B connector, JM3
- Programmable quad clock generator, U2
- 64 MByte QSPI Flash, U6
- 8 Gbit DDR4 SDRAM, U4
- 8 Gbit DDR4 SDRAM, U5
- System Controller CPLD, U18
- Low-dropout (LDO) linear regulator (MGTAUX), U9
- Ultra-low power low-dropout (LDO) regulator (VBATT), U19
Initial Delivery State
Storage device name | Content | Notes |
---|---|---|
System Controller CPLD | Default firmware | - |
OTP Flash area | Empty | Not programmed |
Quad clock generator OTP area | Empty | Not programmed |
Table 1: TE0841-02 module initial delivery state of programmable on-board devices
Boot Process
By default the configuration mode pins M[2:0] of the FPGA are set to QSPI mode (Master SPI), hence the FPGA is configured from serial NOR flash at system start-up. The JTAG interface of the module is provided for storing the initial FPGA configuration data to the QSPI flash memory.
Signals, Interfaces and Pins
Board to Board (B2B) I/Os
I/O signals connected to the SoCs I/O bank and B2B connector:
FPGA Bank | Type | B2B Connector | I/O Signal Count | Bank VCCO Voltage | Notes |
---|---|---|---|---|---|
64 | HR | JM1 | 48 IO's, 24 LVDS pairs | B64_VCCO | Supplied by the carrier board |
65 | HR | JM1 | 8 IO's | 3.3V | On-module power supply |
65 | HR | JM3 | 4 IO's | 3.3V | On-module power supply |
66 | HP | JM3 | 16 IO's, 8 LVDS pairs | B66_VCCO | Supplied by the carrier board |
67 | HP | JM2 | 48 IO's, 24 LVDS pairs | B67_VCCO | Supplied by the carrier board |
67 | HP | JM2 | 2 IO's | B67_VCCO | Supplied by the carrier board |
68 | HP | JM2 | 18 IO's, 9 LVDS pairs | B68_VCCO | Supplied by the carrier board |
Table 2: General overview of FPGA's PL I/O signals connected to the B2B connectors
For detailed information about the pin out, please refer to the Pin-out Tables.
MGT Lanes
MGT (Multi Gigabit Transceiver) lane consists of one transmit and one receive (TX/RX) differential pairs, two signals each or four signals total per one MGT lane. Following table lists lane number, MGT bank number, transceiver type, signal schematic name, board-to-board pin connection and FPGA pins connection:
Lane | Bank | Type | Signal Name | B2B Pin | FPGA Pin |
---|---|---|---|---|---|
0 | 225 | GTH |
|
|
|
1 | 225 | GTH |
|
|
|
2 | 225 | GTH |
|
|
|
3 | 225 | GTH |
|
|
|
4 | 224 | GTH |
|
|
|
5 | 224 | GTH |
|
|
|
6 | 224 | GTH |
|
|
|
7 | 224 | GTH |
|
|
|
Table 3: FPGA to B2B connectors routed MGT lanes overview
Below are listed MGT banks reference clock sources:
Clock signal | Bank | Source | FPGA Pin | Notes |
---|---|---|---|---|
MGT_CLK0_P | 225 | B2B, JM3-33 | MGTREFCLK0P_225, Y6 | Supplied by the carrier board. |
MGT_CLK0_N | B2B, JM3-31 | MGTREFCLK0N_225, Y5 | ||
MGT_CLK1_P | 225 | U2, CLK1B | MGTREFCLK1P_225, V6 | On-board Si5338A. |
MGT_CLK1_N | U2, CLK1A | MGTREFCLK1N_225, V5 | ||
MGT_CLK2_P | 224 | B2B, JM3-34 | MGTREFCLK2P_224, AD6 | Supplied by the carrier board. |
MGT_CLK2_N | B2B, JM3-32 | MGTREFCLK2N_224, AD5 | ||
MGT_CLK3_P | 224 | U2, CLK2B | MGTREFCLK3P_224, AB6 | On-board Si5338A. |
MGT_CLK3_N | U2, CLK2B | MGTREFCLK3N_224, AB5 |
Table 4: MGT reference clock sources
JTAG Interface
JTAG access to the Xilinx Kintex UltraScale FPGA is available through B2B connector JM2.
JTAG Signal | B2B Connector Pin |
---|---|
TMS | JM2-93 |
TDI | JM2-95 |
TDO | JM2-97 |
TCK | JM2-99 |
Table 5: JTAG interface signals
System Controller CPLD I/O Pins
Special purpose pins are connected to the System Controller CPLD and have following default configuration:
Pin Name | SC CPLD Direction | Function | Default Configuration |
---|---|---|---|
JTAGMODE | Input | JTAG select | Low for normal operation. |
nRST_SC0 | Input | Reset | Low active board reset input |
SC1 | - | - | not currently used ('BOOTMODE' in default B2B pin out') |
SC2 | Input / Output | - | Power good signal ('PGOOD' in default B2B pin out) |
SC3 | Input | - | Power enable pin ('EN1' in default B2B pin out) |
SC4 | - | - | not currently used ('NOSEQ' in default B2B pin out') |
F_TCK | Output | JTAG signals between | B2B JTAG signals are forwarded to the FPGA through SC CPLD. |
F_TMS | Output | ||
F_TDI | Output | ||
F_TDO | Input | ||
TCK | Input | JTAG signals between SC CPLD and B2B connector | Program FPGA or SC CPLD depending on pin JTAGMODE. |
TMS | Input | ||
TDI | Input | ||
TDO | Output | ||
PROG_B | Output | FPGA configuration | PL configuration reset signal. |
DONE | Input | FPGA configuration done | PL configuration completed. |
PUDC_B | Output | Pull up during configuration | PL I/O's are 3-stated until configuration of the FPGA completes. |
INIT_B | Input | Initialization done | Low active FPGA initialization pin or configuration error signal. |
EN_PL | Input | Enable PL Power DC-DC converters | Set to contant logical high. |
CPLD_IO | Output | user I/O | Connected to FPGA Bank 45, pin P28. |
Table 6: System Controller CPLD I/O pins
For detailed function of the pins and signals, the internal signal assignment and the implemented logic, look to the Wiki reference page of the module's SC CPLD or into its bitstream file.
Quad SPI Interface
Quad SPI interface is connected to the FPGA configuration bank 0.
Signal Name | QSPI Flash Memory U6 Pin | FPGA Pin |
---|---|---|
SPI_CS | C2 | RDWR_FCS_B_0, AH7 |
SPI_D0 | D3 | D00_MOSI_0, AA7 |
SPI_D1 | D2 | D01_DIN_0, Y7 |
SPI_D2 | C4 | D02_0, U7 |
SPI_D3 | D4 | D03_0, V7 |
SPI_CLK | B2 | CCLK_0, V11 |
Table 7: Quad SPI interface signals and connections
I2C Interface
On-module I²C interface is routed from PL bank 65 I/O pins (PLL_SCL and PLL_SDA) to the I²C interface of Si5338 PLL quad clock generator U2, also two further pins of bank 65 can be used as external I²C interface of the modue:
I²C Interface | Schematic net names | Connected to | I²C Address | Notes |
---|---|---|---|---|
PL bank 65 I/O | 'PLL_SCL', pin AB20 'PLL_SDA' pin AB19 | Si5338 U2, pin 12 Si5338 U2, pin 19 | 0x70 | default address |
PL bank 65 I/O | 'B65_SCL', pin Y19 'B65_SDA', pin AA19 | B2B JM1, pin 95 B2B JM1, pin 93 | - |
Table 8: I2C slave device addresses
On-board Peripherals
System Controller CPLD
The System Controller CPLD (U2) is provided by Lattice Semiconductor LCMXO2-256HC (MachXO2 Product Family). The SC-CPLD is the central system management unit where essential control signals are logically linked by the implemented logic in CPLD firmware, which generates output signals to control the system, the on-board peripherals and the interfaces. Interfaces like JTAG and I2C between the on-board peripherals and to the FPGA module are by-passed, forwarded and controlled by the System Controller CPLD.
Other tasks of the System Controller CPLD are the monitoring of the power-on sequence and to display the programming state of the FPGA module.
For detailed information, refer to the reference page of the SC CPLD firmware of this module.
DDR Memory
By default TE0841 module has two K4A8G165WB-BIRC DDR4 SDRAM chips arranged into 32-bit wide memory bus providing total of 2 GBytes of on-module RAM. Different memory sizes are available optionally.
Quad SPI Flash Memory
On-module QSPI flash memory (U6) on the TE0841-01 is provided by Micron Serial NOR Flash Memory N25Q512A11G1240E with 512-Mbit (64 MByte) storage capacity. This non volatile memory is used to store initial FPGA configuration. Besides FPGA configuration, remaining free flash memory can be used for user application and data storage. All four SPI data lines are connected to the FPGA allowing x1, x2 or x4 data bus widths. Maximum data rate depends on the selected bus width and clock frequency used.
SPI Flash QE (Quad Enable) bit must be set to high or FPGA is unable to load its configuration from flash during power-on. By default this bit is set to high at the manufacturing plant.
Programmable Clock Generator
There is a Silicon Labs I2C programmable quad PLL clock generator on-board (Si5338A, U2) to generate various reference clocks for the module.
Si5338A Pin | Signal Name / Description | Connected to | Direction | Note |
---|---|---|---|---|
IN1 | - | not connected | Input | not used |
IN2 | - | GND | Input | not used |
IN3 | Reference input clock | U3, pin 3 | Input | 25.000000 MHz oscillator, Si8208AI |
IN4 | - | GND | Input | I2C slave device address LSB. |
IN5 | - | not connected | Input | not used |
IN6 | - | GND | Input | not used |
CLK0A | CLK1_P | U1, R23 | Output | FPGA bank 45, default 100MHz* |
CLK0B | CLK1_N | U1, P23 | ||
CLK1A | MGT_CLK1_N | U1, V5 | Output | FPGA MGT bank 225 reference clock, default 125MHz* |
CLK1B | MGT_CLK1_P | U1, V6 | ||
CLK2A | MGT_CLK3_N | U1, AB5 | Output | FPGA MGT bank 224 reference clock, default 156,25MHz* |
CLK2B | MGT_CLK3_P | U1, AB6 | ||
CLK3A | CLK0_P | U1, pin T24 | Output | FPGA bank 45, default 156,25MHz* |
CLK3B | CLK0_N | U1, pin T25 |
Table 9: Programmable quad PLL clock generator inputs and outputs, *PCB REV01 is not programmed
Oscillators
The FPGA module has following reference clocking signals provided by external baseboard sources and on-board oscillators:
Clock Source | Frequency | Signal Name | Clock Destination | Notes |
---|---|---|---|---|
U3, SiT8208AI | 25.000000 MHz | CLK | Si5338A PLL U2, pin 3 (IN3) | - |
U11, DSC1123DL5 | 200.0000 MHz | CLK200M_P | FPGA bank 45, pin R25 | Enable by FPGA bank 65, pin AF24 Signal: 'ENOSC' |
CLK200M_N | FPGA bank 45, pin R26 |
Table 10: Reference clock signals
On-board LEDs
LED | Color | Connected to | Description and Notes |
---|---|---|---|
D1 | Green | System Controller CPLD, bank 3 | Exact function is defined by SC CPLD firmware. |
Table 11: On-board LEDs
Power and Power-On Sequence
Power Consumption
The maximum power consumption of a module mainly depends on the design running on the FPGA.
Xilinx provide a power estimator excel sheets to calculate power consumption. It's also possible to evaluate the power consumption of the developed design with Vivado. See also Trenz Electronic Wiki FAQ.
Power Input | Typical Current |
---|---|
VIN | TBD* |
3.3VIN | TBD* |
Table 12: Typical power consumption
* TBD - To Be Determined soon with reference design setup.
Single 3.3V power supply with minimum current capability of 4A for system startup is recommended.
For the lowest power consumption and highest efficiency of the on-board DC-DC regulators it is recommended to power the module from one single 3.3V supply. All input power supplies should have a nominal value of 3.3V. Although the input power supplies can be powered up in any order, it is recommended to power them up simultaneously.
Power Distribution Dependencies
See also Xilinx datasheet DS892 for additional information. User should also check related base board documentation when intending base board design for TE0841 module.
Power-On Sequence
The TE0841 SoM meets the recommended criteria to power up the Xilinx FPGA properly by keeping a specific sequence of enabling the on-board DC-DC converters dedicated to the particular functional units of the FPGA chip and powering up the on-board voltages.
Following diagram clarifies the sequence of enabling the particular on-board voltages, which will power-up in descending order as listed in the blocks of the diagram:
Power Rails
Power Rail Name | B2B JM1 Pins | B2B JM2 Pins | Input/Output | Notes |
---|---|---|---|---|
VIN | 1, 3, 5 | 2, 4, 6, 8 | Input | Supply voltage. |
3.3VIN | 13, 15 | - | Input | Supply voltage. |
B64_VCO | 9, 11 | - | Input | HR (High Range) bank voltage. |
B66_VCO | - | 1, 3 | Input | HP (High Performance) bank voltage. |
B67_VCO | - | 7, 9 | Input | HP (High Performance) bank voltage. |
B68_VCO | - | 5 | Input | HP (High Performance) bank voltage. |
VBAT_IN | 79 | - | Input | RTC battery supply voltage. |
3.3V | - | 10, 12, 91 | Output | Module on-board 3.3V voltage level. |
Table 13: Module power rails
Current rating of Samtec Razor Beam™ LSHM B2B connectors is 2.0A per pin (2 adjacent pins powered).
Bank Voltages
Bank | Schematic Name | Voltage | Voltage Range |
---|---|---|---|
0 (config) | PL_1.8V | 1.8V | - |
44 HP | DDR_1V2 | 1.2V | HP: 1.2V to 1.8V |
45 HP | PL_1.8V | 1.8V | HP: 1.2V to 1.8V |
46 HP | DDR_1V2 | 1.2V | HP: 1.2V to 1.8V |
64 HR | B64_VCO | user | HR: 1.2V to 3.3V |
65 HR | 3.3V | 3.3V | HR: 1.2V to 3.3V |
66 HP | B66_VCO | user | HP: 1.2V to 1.8V |
67 HP | B67_VCO | user | HP: 1.2V to 1.8V |
68 HP | B68_VCO | user | HP: 1.2V to 1.8V |
Table 14: Module PL I/O bank voltages
Board to Board Connectors
These connectors are hermaphroditic. Odd pin numbers on the module are connected to even pin numbers on the baseboard and vice versa.
4 x 5 modules use two or three Samtec Razor Beam LSHM connectors on the bottom side.
- 2 x REF-189016-02 (compatible to LSHM-150-04.0-L-DV-A-S-K-TR), (100 pins, "50" per row)
- 1 x REF-189017-02 (compatible to LSHM-130-04.0-L-DV-A-S-K-TR), (60 pins, "30" per row) (depending on module)
Connector Mating height
When using the same type on baseboard, the mating height is 8mm. Other mating heights are possible by using connectors with a different height
Order number | Connector on baseboard | compatible to | Mating height |
---|---|---|---|
23836 | REF-189016-01 | LSHM-150-02.5-L-DV-A-S-K-TR | 6.5 mm |
LSHM-150-03.0-L-DV-A-S-K-TR | LSHM-150-03.0-L-DV-A-S-K-TR | 7.0 mm | |
23838 | REF-189016-02 | LSHM-150-04.0-L-DV-A-S-K-TR | 8.0 mm |
LSHM-150-06.0-L-DV-A-S-K-TR | LSHM-150-06.0-L-DV-A-S-K-TR | 10.0mm | |
26125 | REF-189017-01 | LSHM-130-02.5-L-DV-A-S-K-TR | 6.5 mm |
LSHM-130-03.0-L-DV-A-S-K-TR | LSHM-130-03.0-L-DV-A-S-K-TR | 7.0 mm | |
24903 | REF-189017-02 | LSHM-130-04.0-L-DV-A-S-K-TR | 8.0 mm |
LSHM-130-06.0-L-DV-A-S-K-TR | LSHM-130-06.0-L-DV-A-S-K-TR | 10.0mm |
The module can be manufactured using other connectors upon request.
Connector Speed Ratings
The LSHM connector speed rating depends on the stacking height; please see the following table:
Stacking height | Speed rating |
---|---|
12 mm, Single-Ended | 7.5 GHz / 15 Gbps |
12 mm, Differential | 6.5 GHz / 13 Gbps |
5 mm, Single-Ended | 11.5 GHz / 23 Gbps |
5 mm, Differential | 7.0 GHz / 14 Gbps |
Current Rating
Current rating of Samtec Razor Beam™ LSHM B2B connectors is 2.0A per pin (2 adjacent pins powered).
Connector Mechanical Ratings
- Shock: 100G, 6 ms Sine
- Vibration: 7.5G random, 2 hours per axis, 3 axes total
Manufacturer Documentation
Variants Currently In Production
See also the current available variants on the Trenz Electronic shop page
Trenz shop TE0841 overview page | |
---|---|
English page | German page |
Technical Specifications
Absolute Maximum Ratings
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
VIN supply voltage | -0.3 | 6.0 | V | EN63A0QI, TPS74401RGW datasheets |
3.3VIN supply voltage | -0.1 | 3.4 | V | Xilinx datasheet DS892 (HR Bank VCCO) |
VBAT_IN | -0.3 | 6.0 | V | TPS780xx datasheet |
Supply voltage for HR I/O banks (VCCO) | -0.500 | 3.400 | V | Xilinx datasheet DS892 |
Supply voltage for HP I/O banks (VCCO) | -0.500 | 2.000 | V | Xilinx datasheet DS892 |
I/O input voltage for HR I/O banks | -0.400 | VCCO + 0.550 | V | Xilinx datasheet DS892 |
I/O input voltage for HP I/O banks | -0.550 | VCCO + 0.550 | V | Xilinx datasheet DS892 |
GTH and GTY transceiver reference clocks absolute input voltage (MGT_CLK0, MGT_CLK2) | -0.500 | 1.320 | V | Xilinx datasheet DS892 |
GTH and GTY transceiver receiver (RXP/RXN) and transmitter (TXP/TXN) absolute input voltage | -0.500 | 1.260 | V | Xilinx datasheet DS892 |
Storage temperature | -40 | +100 | °C | SML-P11 LED datasheet |
Table 16: Module absolute maximum ratings
Recommended Operating Conditions
Parameter | Min | Max | Units | Reference Document |
---|---|---|---|---|
VIN supply voltage | 3.3 | 5.5 | V | TPS82085SIL, TPS74401RGW datasheet |
3.3VIN supply voltage | 3.3 | 3.4 | V | Xilinx datasheet DS892 (HR Bank VCCO) |
VBAT_IN | 2.2 | 5.5 | V | TPS780xx datasheet |
Supply voltage for HR I/O banks (VCCO) | 1.140 | 3.400 | V | Xilinx datasheet DS892 |
Supply voltage for HP I/O banks (VCCO) | 0.950 | 1.890 | V | Xilinx datasheet DS892 |
I/O input voltage for HR I/O banks | –0.200 | VCCO + 0.20 | V | Xilinx datasheet DS892 |
I/O input voltage for HP I/O banks | –0.200 | VCCO + 0.20 | V | Xilinx datasheet DS892 |
I/O input voltage for SC CPLD U18 | -0.3 | 3.6 | V | LCMXO2-256HC datasheet |
Industrial Module Operating Temperature Range | -40 | 85 | °C | Xilinx datasheet DS892 |
Commercial Module Operating Temperature Range | 0 | 85 | Xilinx DS892, Silicon Labs Si5338 datasheet |
Table 17: Module recommended operating conditions
Module operating temperature range depends also on customer design and cooling solution. Please contact us for options.
Physical Dimensions
Module size: 50 mm × 40 mm. Please download the assembly diagram for exact numbers.
Mating height with standard connectors: 8 mm.
PCB thickness: 1.65 mm.
Highest part on PCB: approximately 3 mm. Please download the step model for exact numbers.
All dimensions are given in millimeters.
Revision History
Hardware Revision History
Date | Revision | Notes | PCN | Documentation Link |
---|---|---|---|---|
2018-05-11 | 02 | current available board revision | PCN-20180511 | TE0841-02 |
2015-12-09 | 01 | First production release | - | TE0841-01 |
Table 18: Module hardware revision history
Hardware revision number can be found on the PCB board together with the module model number separated by the dash.
Document Change History
Document Change History
Date | Revision | Contributors | Description |
---|---|---|---|
| |||
v.58 | John Hartfiel |
| |
v.57 | Jan Kumann, Ali Naseri | Initial document. |
Table 18: Document change history.
Disclaimer
Data Privacy
Please also note our data protection declaration at https://www.trenz-electronic.de/en/Data-protection-Privacy
Document Warranty
The material contained in this document is provided “as is” and is subject to being changed at any time without notice. Trenz Electronic does not warrant the accuracy and completeness of the materials in this document. Further, to the maximum extent permitted by applicable law, Trenz Electronic disclaims all warranties, either express or implied, with regard to this document and any information contained herein, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non infringement of intellectual property. Trenz Electronic shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein.
Limitation of Liability
In no event will Trenz Electronic, its suppliers, or other third parties mentioned in this document be liable for any damages whatsoever (including, without limitation, those resulting from lost profits, lost data or business interruption) arising out of the use, inability to use, or the results of use of this document, any documents linked to this document, or the materials or information contained at any or all such documents. If your use of the materials or information from this document results in the need for servicing, repair or correction of equipment or data, you assume all costs thereof.
Copyright Notice
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Trenz Electronic.
Technology Licenses
The hardware / firmware / software described in this document are furnished under a license and may be used /modified / copied only in accordance with the terms of such license.
Environmental Protection
To confront directly with the responsibility toward the environment, the global community and eventually also oneself. Such a resolution should be integral part not only of everybody's life. Also enterprises shall be conscious of their social responsibility and contribute to the preservation of our common living space. That is why Trenz Electronic invests in the protection of our Environment.
REACH, RoHS and WEEE
REACH
Trenz Electronic is a manufacturer and a distributor of electronic products. It is therefore a so called downstream user in the sense of REACH. The products we supply to you are solely non-chemical products (goods). Moreover and under normal and reasonably foreseeable circumstances of application, the goods supplied to you shall not release any substance. For that, Trenz Electronic is obliged to neither register nor to provide safety data sheet. According to present knowledge and to best of our knowledge, no SVHC (Substances of Very High Concern) on the Candidate List are contained in our products. Furthermore, we will immediately and unsolicited inform our customers in compliance with REACH - Article 33 if any substance present in our goods (above a concentration of 0,1 % weight by weight) will be classified as SVHC by the European Chemicals Agency (ECHA).
RoHS
Trenz Electronic GmbH herewith declares that all its products are developed, manufactured and distributed RoHS compliant.
WEEE
Information for users within the European Union in accordance with Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003 on waste electrical and electronic equipment (WEEE).
Users of electrical and electronic equipment in private households are required not to dispose of waste electrical and electronic equipment as unsorted municipal waste and to collect such waste electrical and electronic equipment separately. By the 13 August 2005, Member States shall have ensured that systems are set up allowing final holders and distributors to return waste electrical and electronic equipment at least free of charge. Member States shall ensure the availability and accessibility of the necessary collection facilities. Separate collection is the precondition to ensure specific treatment and recycling of waste electrical and electronic equipment and is necessary to achieve the chosen level of protection of human health and the environment in the European Union. Consumers have to actively contribute to the success of such collection and the return of waste electrical and electronic equipment. Presence of hazardous substances in electrical and electronic equipment results in potential effects on the environment and human health. The symbol consisting of the crossed-out wheeled bin indicates separate collection for waste electrical and electronic equipment.
Trenz Electronic is registered under WEEE-Reg.-Nr. DE97922676.